Troubleshooting - Triton T12 OT Instrucciones De Uso

allow dust, wood chippings and swarf to build up. Use a vacuum cleaner to keep the work
space clean, especially in confined areas.
WARNING: DO NOT inhale dust. Wear adequate breathing protection. Some dusts may be
toxic especially from man-made composite materials.
Sawing
• Ensure the saw blade is sharp and in good condition
• Do not use saw blades that are damaged or deformed in any way
• When sawing light building materials, follow the recommendations of the material suppliers
• Apply plunge cuts to soft materials ONLY, for example, wood, gypsum plasterboard etc.
(image F)
• If using saw blades not designed for cutting metal, ensure there are no nails or screws
embedded in the workpiece. If necessary, remove embedded objects or use metal cutting
saw blades instead
Sanding
• The removal rate and the sanding pattern are determined by the type of sanding sheet, the
preset oscillation rate and the applied pressure
• Pay particular attention to applying uniform sanding pressure; this increases the working
life of the sanding sheets
• Intensifying the sanding pressure will not lead to an increase of the sanding capacity, but to
increased wear of the machine and the sanding sheet
• For precise on-the-spot sanding of edges, corners and hard to reach areas, it is also
possible to work only with the tip or an edge of the sanding plate (Fig. G)
• A sanding sheet that has been used for sanding metal should not be used for sanding
other materials
• Regularly brush down or vacuum the surface being sanded to ensure the sanding sheet is
in direct contact with the surface
Scraping
• For scraping, select a high speed setting
• On soft surfaces (e.g. wood), work at a flat angle and apply only light pressure so that the
scraper does not cut into the surface

Troubleshooting

Problem
Red LED does not illuminate and Battery (5) not charging
Battery has low capacity
Tool cannot be switched on
Tool stops operating during use
GB
Blade not cutting correctly
8
Accessories
A full range of accessories and products is available from your Triton stockist.
• T12B – T12 1.5Ah Li-Ion Battery 12V
• T12HCB – T12 Hi-Cap 3.0Ah Li-Ion Battery 12V
Additional Triton products compatible with the included batteries:
• T12CH – T12 Combi Hammer Drill 12V
• T12AD – T12 Angle Drill 12V
• T12DD – T12 Drill Driver 12V
• T12ID – T12 Impact Driver 12V
• T12RS – T12 Reciprocating Saw 12V
• T12FL – T12 Swivel Head Torch 12V
Spare parts can be purchased from your Triton dealer or online at www.toolsparesonline.com
Maintenance
WARNING: Always disconnect the battery from the tool before attaching or removing
accessories, making any adjustments or performing maintenance.
• This tool is manufactured using class-leading components and uses intelligent circuitry that
protects the tool and its components. In normal use it should provide a long working life
Cleaning
• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear quickly,
and shorten the machine's service life. Clean the body of your machine with a soft brush or
dry cloth. If available, use clean, dry, compressed air to blow through the ventilation holes
Storage
• Store this tool and its accessories after use in its case, in a dry, secure place out of the
reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer
functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),
with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
Possible cause
Battery not fully seated
Battery Charger (11) not powered
Battery not being fully charged
Battery has been charged over 200 times and capacity has
started to reduce
Battery discharged
Defective battery
Tool defective
Battery has low charge
Over temperature safety feature has operated
Over current safety feature has operated
Speed setting low
Material may not be suitable for blade
Material not suitable for tool
Blade may be worn
Solution
Refit Battery correctly
Recheck mains connection
Wait until green LED is illuminated
This is normal for batteries. Contact your Triton dealer to
purchase a replacement battery
Recharge battery or replace with a charged battery
Replace battery
Contact your Triton dealer or authorised service centre
Charge battery fully before use especially before jobs that
are more difficult to cut
Tool may require up to 30 minutes for tool to reset. A slower
speed setting may be required to prevent this safety feature
operating. Check Motor Vents (2) are not blocked. Reduce
the amount of hand pressure on the tool to reduce load
on the motor
Tool may require up to 1 minute to reset. A slower speed
setting may be required. Check Motor Vents are not blocked.
Reduce the amount of hand pressure on the tool to reduce
load on the motor
Increase speed
Change blade
Some materials including hardened metals have no
compatible blade
Replace blade