Metabo H 16-500 Instrucciones De Manejo página 5

may contain flammable materials that could be
ignited by the heat gun when working in these
locations. The ignition of these materials may not
be readily apparent and could result in property
damage and injury to persons. Do not use if in
doubt about this hazard. When working in these
locations, keep the heat gun moving in a back-
and-forth motion. Lingering or pausing in one
spot could ignite the panel or the material behind
it.
2. This heat gun can produce up to 1200°F of
flameless heat at the nozzle. Do not direct
airstream at clothing, hair or other body parts. Do
not use as a hair dryer.
3. Do not use near flammable liquids or in an
explosive environment (fumes, gases or dust).
Remove materials or debris, that may become
ignited, from work area.
4. Always hold tool by plastic enclosure. The metal
nozzle requires approximately 20 minutes to
cool to where it can be touched. Do not touch
nozzle or accessory tips until cool.
5. Do not store tool until nozzle has cooled to room
temperature. Place tool in a clear area away from
combustible materials while cooling.
6. Do not cut off airflow by placing nozzle too close
to workpiece. Keep intake vents clean and clear
of obstructions.
7. Place tool on a level surface with the support
rubber ring when tool is not hand held. Place
cord in a position that won't cause tipping.
8. Do not leave tool unattended while running or
cooling down. Otherwise risk of fire.
9. Keep a fully charged fire extinguisher nearby.
10. Do not direct airflow directly on glass.
11. Shield materials around the heated area to
prevent damage or fire.
12. Use only with 120 V AC voltage.
13. Do not use in wet conditions.
14. Not to be used by children. This is not a toy and
should be respected.
15. Do not use in bath or over water.
16. Safety glasses should be worn when using this
tool.
17. It is recommended that leather gloves be worn
when using a heat gun.
18. Always unplug after use.
19. WARNING: Extreme care should be taken
when stripping paint. The peelings, residue and
vapors of paint may contain lead, which is
poisonous. Any pre-1977 paint may contain lead
and paint applied to homes prior to 1950 is likely
to contain lead. Once deposited on surfaces,
hand to mouth contact can result in the ingestion
of lead. Exposure to even low levels of lead can
cause irreversible brain and nervous system
damage; young and unborn children are
particularly vulnerable. Before beginning any
paint removal process you should determine
whether the paint you are removing contains
lead. This can be done by your local health
department or by a professional who uses a
paint analyzer to check the lead contact of the
paint to be removed. LEAD-BASED PAINT
SHOULD ONLY BE REMOVED BY A
PROFESSIONAL AND SHOULD NOT BE
REMOVED USING A HEAT GUN.
Persons removing paint should follow these guide-
lines.
1. Move the work piece outdoors. If this is not
possible, keep the work area well ventilated.
Open the windows and put an exhaust fan in one
of them. Be sure the fan is moving the air from
inside to outside.
2. Remove or cover any carpets, rugs, furniture,
clothing, cooking utensils and air ducts.
3. Place drop cloths in the work area to catch any
residue. Wear protective clothing such as extra
work shirts, overalls and hats.
4. Work in one room at a time. Furnishings should
be removed or placed in the center of the room
and covered. Work areas should be sealed off
from the rest of the dwelling by sealing doorways
with drop cloths.
5. Children, pregnant or potentially pregnant
women and nursing mothers should not be
presentin the work area until the work is done
and all clean up is complete.
6. Wear a dust respirator mask or a dual filter (dust
and fume) respirator mask which has been
approved by the Occupational Safety and Health
Administration (OSHA), the National Institute of
Safety and Health (NIOSH), or the United States
Bureau of Mines. These masks and replaceable
filters are readily available at major hardware
stores. Be sure the mask fits. Beards and facial
hair may keep masks from sealing properly.
Change filters often. DISPOSABLE PAPER
MASKS ARE NOT ADEQUATE.
7. Use caution when operating the heat gun. Keep
the heat gun moving as excessive heat will
generate fumes which can be inhaled by the
operator.
8. Keep food and drink out of the work area. Wash
hands, arms and face and rinse mouth before
eating or drinking. Do not smoke or chew gum or
tobacco in the work area.
9. Clean up all removed residue and dust by wet
mopping the floors. Use a wet cloth to clean all
walls, sills and any other surface where residue
or dust is clinging. DO NOT SWEEP, DRY DUST
OR VACUUM. Use a high phosphate detergent
or trisodium phosphate (TSP) to wash and mop
areas.
10. At the end of each work session put the residue
and debris in a double plastic bag, close it with
tape or twist ties, and dispose of properly.
11. Remove protective clothing and work shoes in
the work area to avoid carrying dust into the rest
of the dwelling. Wash work clothes separately.
Wipe shoes off with a wet rag that is then
washed with the work clothes. Wash hair and
body thoroughly with soap and water.
SAVE THESE INSTRUCTIONS
ENGLISH
ENG
5