Use - Metabo H 16-500 Instrucciones De Manejo

6 Buttons for setting the temperature*
7 Buttons for setting the air volume*
8 Program selection button*
9 Display* (for temperature and speed)
10 Save button* (for saving changed programs)
11 Adjusting wheel for setting the temperature*
* depending on the features / model

5 Use

Before plugging in, check that the rated
mains voltage and mains frequency, as
stated on the rating label, match with your power
supply.
The distance to the object being processed
depends on the material and intended
processing type. Always first carry out an inspec-
tion of air volume and temperature! The attachable
nozzles (see chapter 8) available as accessories
can be used for precise hot air control to a specific
point or a surface.
Take care when changing hot nozzles!
Danger of burns.
5.1 H 16-500
The sliding switch (4) can be used to switch the
tool on and off and for selecting between 2 stages
(for air volume and temperature).
Stage 1: 750 °F, 8.5 cf/min
Stage 2: 1100 °F, 14.8 cf/min
5.2 HE 20-600
The sliding switch (4) can be used to switch the
tool on and off and for selecting between 3 stages.
The air volume is varied in the three stages from
3.6/10.6/15.0 cf/min.
At stage 1 of the sliding switch (4) the temperature
is always 120 °F (cold-air stage). Use the cold-air
stage to dry paint, cool workpieces or to cool
down the nozzle before changing an accessory
part.
At stage 2 and 3 of the sliding switch (4) the
temperature can be set steplessly at the adjusting
wheel (11).
The numbers 1 - 9 shown on the adjusting wheel
are used for orientation. "1" means 120 °F. "9"
means 1100 °F (maximum temperature).
5.3 HE 23-650 Control
The sliding switch (4) can be used to switch the
tool on and off and for selecting between 2 stages.
Setting temperature:
At stage 1 of the sliding switch (4) the temperature
is always 120 °F (cold-air stage). Use the cold-air
stage to dry paint, cool workpieces or to cool
down the nozzle before changing an accessory
part.
At stage 2 of the sliding switch (4) the temperature
can be set steplessly.
Press the buttons (6) to set the temper-
ature.
Briefly press the "+" /"-" buttons to
increase or lower the set value in 10°F
steps. Press the buttons longer to change the
value faster.
Notes:
Triangles are displayed when
the desired temperature is
being set.
If the desired temperature is
set, the blower (depending
on the selected speed/air
volume) needs a few seconds to reach the set
value. The triangles flash during this period.
The actual temperature is
measured at the nozzle
outlet. The triangles disap-
pear when the desired temperature has been
reached.
When the heat gun is switched off, the last value
set is retained.
Setting air volume:
Press the buttons (7) to set the air
volume or the fan speed.
Program operation:
Four programs for the most frequent types
of work are set in the factory. Press the "P"
button for program operation. A
program 1 appears in the display. Press the
program button again to reach the
programs , and
return to normal operation.
Program 1: Forming plastic pipes
Program 2: Welding plastic pipes
Program 3: Removing paint
Program 4: Soft soldering
(For technical data, see chapter 11)
Changing programs and saving:
The values in the four programs can be
changed and saved. To do this, first press
the program button "P" until the program to
be changed is displayed. Set the desired air
volume and temperature. Then push the
save button (10) until the
ENGLISH
ENG
for
. Press the button again to
symbol in the display
7