Sheet Sander Safety Warnings; Know Your Product - SPARKY MP 250 Instrucciones De Uso

er tool for operations different from those intended
could result in a hazardous situation.
5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of the
power tool is maintained.

Sheet sander safety warnings

Wear hearing protection during continuous
operation. Exposure to noise can cause hear-
ing loss.
During operation provide eye protection to
prevent eyes from exposure to flying par-
ticles. Wear goggles.
Take protective measures against inhala-
tion of dust. Some materials can contain
toxic ingredients. Wear a dust mask and work
with dust/chip extraction when connectable.
▪ Do not process materials containing asbestos. Asbes-
tos is considered carcinogenic.
▪ Use of protective gloves is recommended.
WARNING:
Before connecting a tool to a
power source be sure that the voltage supply is the
same as that specified on the nameplate of the tool.
▪ A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
▪ Fully unwind cable drum extensions to avoid potential
overheating.
▪ When an extension cable is required, you must en-
sure that it has the right ampere rating for your power
tool and it is in safe electrical condition.
WARNING:
Always switch off and unplug
the power tool prior to any adjustment, servicing or
maintenance or in case of mains drop-out.
▪ Use the power tool for dry sanding only.
▪ Use clamps or a vice to secure your work whenever
possible.
▪ Use perforated hook-and-loop sandpaper with the
prescribed dimensions.
▪ A sanding sheet that has been used for metal should
not be used for other materials.
▪ Never switch on the orbital sander under load and
leave it down only after final arrest.
▪ Do not overload the machine: operate with moderate
pressure. Overloading occurs when you apply exces-
sive pressure, resulting in decrease of motor speed,
which may cause inefficient operation and possible
fault of the motor.
Original instructions
▪ Keep work area clean. Blends of materials are par-
ticularly dangerous. Dust from light alloys can burn or
explode.
▪ The presence of harmful toxic dust, separated during
processing materials containing lead, quartz (Silicium
Dioxide), touching or inhaling it may be hazardous to
the health of the operator or observers.
▪ Always keep the cord away from the working area of
the power tool.
▪ Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains plug
when the cable is damaged while operating. Dam-
aged cables increase the risk of electric shock.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and
not the manufacturer shall be liable for any damage
or injury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its po-
tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. ON/OFF switch
2. Power indicator
3. Abrasive sheet (sandpaper) (MP 250)
4. Sanding plate (MP 250)
5. Clamp (MP 250)
6. Dust collector bag
7. Punch guide (MP 250)
8. Dust extraction adapter
9. Multipurpose sanding plate (MP 251)
10. Perforated abrasive sheet (MP 251)
11. Upper abrasive sheet (MP 251)
12. Upper foam pad (MP 251)
13. Multipurpose sanding plate (MP 251)
14. Rectangular perforated abrasive sheet (MP 251)
15. Upper foam pad (MP 251)
16. Upper abrasive sheet (MP 251)
5
EN