Tabla de contenido
Publicidad
EN
- Should you not use any water for an extended period of time, you should:
➣ disconnect the appliance from the electrical supply by switching the external switch to "OFF";
➣ turn off the plumbing circuit taps.
- Hot water at above 50°C flowing out of the taps at the point of use could cause serious scalds or even death
from burns. Children, the disabled and the elderly are more exposed to the risk of burns. It is strictly forbidden
for the user to perform any routine or extraordinary maintenance.
To clean the external parts use a damp cloth soaked in soap and water.
Adjusting the temperature and activating the functions
The product is set to "Manual" by default, with a set of two showers and the function "ECO EVO" is active.
In case of a power failure or if the product is switched off using the button ON/OFF (Ref. A, Fig 9), the last
shower set remains saved.
Slight noise may occur during the heating phase due to the water being heated.
Switch the appliance on by pressing the ON/OFF button (Ref. A, Fig 9) During the heating phase, the lines
on both sides of the display (Ref. C, Fig 9) remain on.
On first installation, the display must be oriented according to the installation of the product. If vertical no
action is required; if horizontal, the display must be oriented accordingly by pressing the "MODE" + "ECO"
simultaneously for 5 seconds.
Setting- changing local time.
To change local time, when the machine is first switched on, the product automatically prompts you to set
the correct time; during subsequent use the "set" button must be held down for 3 seconds. To change current
time, turn the knob and press the "set" button to confirm. Repeat the operation to set minutes.
Programming mode (Manual, Program1, Night).
On each touch of the "Mode" button a different operating mode is selected (indicated by the corresponding
flashing icon). The selection of the functions is cyclical and follows this order: Program1, Manual, Night. The
programs "P1" is set by default for the time band 07:00 and a set of two showers.
"Manual" mode (symbol "
" on).
Allows the user to set the desired temperature simply by turning the knob until the desired temperature is
displayed (Ref. E) and in the display you can see the number of showers available based on the related on
icons . By clicking the set button, the setting is saved. Both during the temperature selection phase and in
the heating phase you can display the waiting time (Ref. F) that the product will take to reach the temperature
(Ref. E).
The "Program 1" (symbol "
" on), allow you to program a time band of the day when you want to have hot
water. Press the "mode" button until the writing related to the desired program starts flashing. Now set the
time at which hot water is desired by turning the knob (select the time by 30 minutes increments). By pres-
sing the "set" button, the time is saved.
To set the number of showers to the desired level, turn the knob and press the "set" button to save the setting.
Press the "set" button to start appliance operation in "P1" mode. During the periods for which the use of hot
water is not explicitly required, water heating is disabled. When the programming function is enabled, the
knob is disabled. If you want to change the parameters, you must press the "set" button.
If the programming functions ("P1") is used in combination with the "ECO" function (see paragraph "ECO
EVO function"), the temperature is set automatically by the appliance and only the desired time bands for
hot water availability can be set.
NB: for any setting, if the user takes no action for 5 seconds, the system saves the last setting.
Night Heating Mode
When the user chooses the night heating mode, the user will set the needed number of people for shower.
Just turn the "SET"knob until the expected number of people for shower appears on the display. Press
"SET"to confirm or wait 3 seconds before the system automatically confirm the selected number of people
for shower. The heating time of the night mode is 23:00-7:00.
Wi-Fi Heating Mode
A smart remote control and programmation of the heating mode is possible using the specific app "Velis
Ariston Net". The app is free and available on Google play and App Store. Please refer to "Wi-Fi Function"
paragraph.
Power-off Memory Function
When reconnected to power after power off, the display panel will show the last operation setting so that the
user can continue the operation setting. If there is no other actions after the display, the system will set cur-
rent operation as default and the setting will automatically disappear in a minute.
24
Publicidad
Tabla de contenido
