Peg-Perego Primo Viaggio i-Plus Instrucciones De Uso página 21

place (fig_a). Make sure that the red/green indicators on the
back of the base are in the green position (fig_b).
2 Press the two buttons on the handlebar, turn them and
position against the vehicle seat.
3 To release the Primo Viaggio i-Plus from the Base i-Size, put
the handlebar in the carry position and pull the lever on the
backrest upwards while simultaneously lifting the car seat.
4 The car seat handlebar has four fixed positions. To rotate it,
press the two buttons on the handlebar and move this to
the required angle. Ensure it clicks into position.
• Position A: the in-vehicle position;
• Position B: the position for transport by hand and for
installation on a base, stroller or chassis;
• Position C: this is the resting position;
• Position D: stops the car seat from rocking.
Instructions for use without base
5 IMPORTANT! The car seat must be parallel to the
ground. If necessary, use rolled-up towels or swimming pool
float tubes under the car seat, in the folds of the vehicle's
seats.
Fit the car seat with the child seated inside, remembering to
secure the child with the harness. Fully lower the handlebar
of the car seat (point 4 -position A).
6 Slide the lower part of the vehicle seatbelt into the two
guides on the car seat handlebar (fig_a) and buckle it (fig_b),
ensuring the seatbelt is taut, as shown in the figure.
Grasp the upper part of the vehicle seatbelt and pass it
behind the car seat backrest(fig_c).
7 Insert the belt into the rear guide (fig_a). Tighten the vehicle
seat belt(fig_b). Installation is now complete.
8 To release the harness, press the red button on the crotch
strap buckle (fig. a) and remove the straps.
engage the harness, place the two shoulder strap tongues in
position and insert them into the buckle of the crotch strap
until they click into place (fig. b).
9 To slacken the harness, insert a finger through the seat opening
(1), keep the metal button pressed, and with the other hand
pull on the straps (2).
10 To tighten the straps until they are snug to the child's body, pull
the central adjustment strap towards you.
CAUTION: Do not over-tighten the straps, and ensure
you leave minimum slack.
11 IMPORTANT! In winter, do not strap the child into the
car seat wearing bulky, heavy clothing, and do not place
blankets between the child's body and the harness. This
could cause incorrect positioning of the safety harness, with
serious consequences in the event of a collision.
Use a blanket or an approved Peg-Perego accessory to
protect your child from the weather.
12 The harness and the "Side Impact Protection" headrest can
be adjusted simultaneously to 5 different heights so as to
follow the growth of the child. To adjust height, open the
door to access the opening in the back of the seat, press the
button on the back of the height adjuster (arrow 1) while
raising or lowering the seat to the desired position, making
sure it is positioned correctly and clicked in place (arrow 2).
Slacken the straps before adjusting the height of the harness
and headrest.
13 The headrest may be set in 6 different positions.
14 The safety harness is at the right height when the slots in the
backrest are at shoulder height or just below (green area), as
shown in the figure.
Make sure the straps are not in the red area.
15 This car seat features the Tri Stage Cushion, a system
composed of 3 separate cushions for even the smallest
babies.
A: headrest reducer;
B: backrest reducer cushion;
C: reducer cushion for small seat. Do not use the Tri Stage
Cushion with children weighing more than 9 kg.
16 The special shell shape is designed to rock your child. To rock
the child gently, put the handlebar in the carry position, as
shown (fig_a).
To prevent oscillation and stop rocking, lock the handlebar
To behind the backrest (fig_b).
17 The hood provides your child with shade and shelter.
Unzip and lower the hood to cover a greater area.
IMPORTANT: The hood must not be used to lift the
car seat because it might detach.
18 To remove the hood: unbutton the 5 buttons on the lower
edge of the hood
19 Release the elastic bands behind the handlebar (1), lift it and
release it upwards (2).
21