Triton TMUTL Instrucciones De Uso página 9

Ocultar thumbs Ver también para TMUTL:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5. Insert the Locking Knob (14) into the Dust Collar Threaded Hole and tighten to fasten the
Dust Extraction Collar (Fig. II)
Note: The installation of the collar must be completed without an accessory installed on the
multi-tool (see 'Fitting a blade or scraper' or 'Fitting the sanding pad & sanding sheets').
Note: The Dust Extraction Port is designed to fit a standard 32mm diameter hose. When
working in confined spaces, the Dust Extraction Port can be removed.
Fitting or removing the Dust Extraction Port
• Once the Dust Extraction Collar (2) is fitted to the multi-tool, the Dust Extraction Port (3) can
be easily removed or installed
• To remove, pull the Dust Extraction Port away from the Dust Extraction Collar
• To install, push the push the Dust Extraction Port onto the Dust Extraction Collar, ensuring
the hole is facing up
Fitting a vacuum hose
Note: The vacuum and hose is not supplied.
1. Push a compatible size vacuum or dust extraction system hose onto the Dust Extraction
Port (3)
2. If working in a confined space with no room for dust extraction, the Dust Extraction Port can
be removed while still attached to the hose, and will be ready for quick reattachment
Selecting the right accessory
Task
Sawing
Sanding
Removing grout
Scraping
We recommend you purchase your accessories from the same store that sold you the multi-tool. Always use good quality accessories. Choose the type according to the task at hand. Refer to the
accessory packaging for more information.
Fitting a blade or scraper
1. Lift the Keyless Change Lever (4) and push forward (Fig. III) then loosen the Flange (12) by
rotating the lever anti-clockwise (Fig. IV). Rotating the Keyless Change Lever in a clockwise
direction will tighten the flange (Fig. IV)
Notes:
• If the accessory is open ended, the Flange can be loosened partially to fit the accessory
(Fig. V)
• If the accessory has a closed end, the Flange will need to be loosened and removed from
the multi-tool to fit the accessory (Fig. V) before re-inserting the Flange. A small amount of
finger pressure on the Flange is necessary when first tightening
• Always ensure the blade is the correctly installed with the curve facing down away from the
multi-tool (Fig. VI)
2. Align the accessory holes with the buttons on the Flange (Fig. VII no. 1&2), hold the
accessory on the head (Fig. VIII), ensuring the buttons are aligned, and rotate the Keyless
Change Lever clockwise to tighten the Flange (Fig. IV)
Note: The blade/accessory can be aligned with the buttons at the desired angle before
tightening the flange (Fig. VII no. 3).
3. Close the lever down to the lock position on the multi-tool (Fig. IX)
IMPORTANT: Ensure the locking tabs are facing the correct way when locking the lever. If
after tightening the flange the tabs are facing the wrong way (Fig. X), move the lever to the
middle position, then rotate the lever vertically until the tabs are facing the locking slots on
the multi-tool (Fig. X).
4. To remove the blade/accessory, repeat steps 1–3 and remove the blade or scraper during
step 2 (Fig. VII no. 1)
Pic
Bi-metal metal/wood end cut blade
HSS segment saw blade
Sanding base
Diamond-coated segment saw blade
Rigid scraper blade
Name
Wood, plastic, fiberglass, nails, non-ferrous
metals, thin sheet metal, hardened fillers
Thin wood, plastic, fiberglass, non-ferrous
metals, thin sheet metal, hardened fillers,
window glazing
Wood, plastic, hardened fillers
Ceramic and stone tile, backerboard
Old paint, hardened adhesive, caulk, carpet
Application
9

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido