Makita HP333D Manual De Instrucciones página 8

Reversing switch action
Fig.5: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
GLUHFWLRQ RI URWDWLRQ EHIRUH WKH WRRO VWRSV PD\ GDP-
age the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
$ VLGH IRU FORFNZLVH URWDWLRQ RU IURP WKH % VLGH IRU FRXQ-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
WLRQ WKH VZLWFK WULJJHU FDQQRW EH SXOOHG
Speed change
Fig.6: 1. Speed change lever
CAUTION:
Always set the speed change lever
fully to the correct position. If you operate the
tool with the speed change lever positioned halfway
EHWZHHQ WKH  VLGH DQG  VLGH WKH WRRO PD\ EH
damaged.
CAUTION:
Do not use the speed change lever
while the tool is running. 7KH WRRO PD\ EH GDPDJHG
Adjusting the fastening torque
Fig.8: 1. $FWLRQ PRGH FKDQJLQJ ULQJ 2. $GMXVWLQJ
ring 3. Graduation 4. $UURZ
7KH IDVWHQLQJ WRUTXH FDQ EH DGMXVWHG LQ  OHYHOV E\ WXUQLQJ WKH DGMXVWLQJ ULQJ $OLJQ WKH JUDGXDWLRQV ZLWK WKH DUURZ
RQ WKH WRRO ERG\ <RX FDQ JHW WKH PLQLPXP IDVWHQLQJ WRUTXH DW  DQG PD[LPXP WRUTXH DW 
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
WRUTXH OHYHO LV UHTXLUHG IRU D SDUWLFXODU DSSOLFDWLRQ 7KH IROORZLQJ VKRZV WKH URXJK JXLGH RI WKH UHODWLRQVKLS EHWZHHQ
the screw size and graduation.
Graduation
Machine screw
Wood Soft wood
screw (e.g. pine)
Hard wood
(e.g. lauan)
1 2 3 4 5
M4
–
Position of
speed
change lever
1
2
7R FKDQJH WKH VSHHG VZLWFK RII WKH WRRO ¿UVW 6HOHFW
WKH  VLGH IRU KLJK VSHHG RU  IRU ORZ VSHHG EXW KLJK
torque. Be sure that the speed change lever is set to the
FRUUHFW SRVLWLRQ EHIRUH RSHUDWLRQ
If the tool speed is coming down extremely during the
operation with "2", slide the lever to the "1" and restart
the operation.
Selecting the action mode
CAUTION:
your desired mode mark. If you operate the tool
with the ring positioned halfway between the
mode marks, the tool may be damaged.
CAUTION:
from "
¿FXOW\ WR VOLGH WKH DFWLRQ PRGH FKDQJLQJ ULQJ ,Q
this case, switch on and run the tool for a second
at the "
the ring to your desired position.
Fig.7: 1. $FWLRQ PRGH FKDQJLQJ ULQJ 2. $GMXVWLQJ
ring 3. Graduation 4. $UURZ
This tool has three action modes.
• Drilling mode (rotation only)
• Hammer drilling mode (rotation with
hammering)
• Screwdriving mode (rotation with clutch)
6HOHFW RQH PRGH VXLWDEOH IRU \RXU ZRUN 7XUQ WKH
action mode changing ring and align the mark that you
VHOHFWHG ZLWK WKH DUURZ RQ WKH WRRO ERG\
6 7 8 9 10 11
–
–
8 ENGLISH
Speed Torque
Low High
High Low
Always set the ring correctly to
When you change the position
" to other modes, it may be a little dif-
" position, then stop the tool and slide
12 13 14 15 16
M5
3.5 x 22
3.5 x 22
Applicable
operation
Heavy load-
ing operation
Light loading
operation
17 18 19 20
M6
4.1 x 38
–
4.1 x 38