Makita HP333D Manual De Instrucciones página 9

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
drill bit
Optional accessory
Fig.9: 1. Sleeve 2. Close 3. Open
Turn the sleeve counterclockwise to open the chuck
MDZV 3ODFH WKH GULYHU ELWGULOO ELW LQ WKH FKXFN DV IDU
as it will go. Turn the sleeve clockwise to tighten the
FKXFN 7R UHPRYH WKH GULYHU ELWGULOO ELW WXUQ WKH VOHHYH
counterclockwise.
Installing hook
CAUTION:
When installing the hook, always
VHFXUH LW ZLWK WKH VFUHZ ¿UPO\ If not, the hook
may come off from the tool and result in the personal
LQMXU\
Fig.10: 1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
7KLV FDQ EH LQVWDOOHG RQ HLWKHU VLGH RI WKH WRRO 7R LQVWDOO
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
Installing driver bit holder
Optional accessory
Fig.11: 1. 'ULYHU ELW KROGHU 2. 'ULYHU ELW
)LW WKH GULYHU ELW KROGHU LQWR WKH SURWUXVLRQ DW WKH WRRO IRRW
on either right or left side and secure it with a screw.
:KHQ QRW XVLQJ WKH GULYHU ELW NHHS LW LQ WKH GULYHU ELW
KROGHUV 'ULYHU ELWV  PPORQJ FDQ EH NHSW WKHUH
OPERATION
CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
UHG LQGLFDWRU RQ WKH XSSHU VLGH RI WKH EXWWRQ LW LV QRW
locked completely. Insert it fully until the red indicator
FDQQRW EH VHHQ ,I QRW LW PD\ DFFLGHQWDOO\ IDOO RXW RI
WKH WRRO FDXVLQJ LQMXU\ WR \RX RU VRPHRQH DURXQG
you.
CAUTION:
When the speed comes down
extremely, reduce the load or stop the tool to
avoid the tool damage.
+ROG WKH WRRO ¿UPO\ ZLWK RQH KDQG RQ WKH JULS DQG WKH
RWKHU KDQG RQ WKH ERWWRP RI WKH EDWWHU\ FDUWULGJH WR
control the twisting action.
Fig.12
Screwdriving operation
CAUTION:
Adjust the adjusting ring to the
proper torque level for your work.
CAUTION:
Make sure that the driver bit is
inserted straight in the screw head, or the screw
and/or driver bit may be damaged.
First, turn the action mode changing ring so that the
DUURZ RQ WKH WRRO ERG\ SRLQWV WR WKH
3ODFH WKH SRLQW RI WKH GULYHU ELW LQ WKH VFUHZ KHDG DQG
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE: When driving wood screw, pre-drill a pilot hole
 WKH GLDPHWHU RI WKH VFUHZ ,W PDNHV GULYLQJ HDVLHU
and prevents splitting of the workpiece.
Hammer drilling operation
CAUTION:
There is a tremendous and sudden
twisting force exerted on the tool/drill bit at the
time of hole breakthrough, when the hole becomes
clogged with chips and particles, or when striking
reinforcing rods embedded in the concrete.
First, turn the action mode changing ring so that the arrow
RQ WKH WRRO ERG\ SRLQWV WR WKH
ULQJ FDQ EH DOLJQHG LQ DQ\ WRUTXH OHYHOV IRU WKLV RSHUDWLRQ
%H VXUH WR XVH D WXQJVWHQFDUELGH WLSSHG GULOO ELW
3RVLWLRQ WKH GULOO ELW DW WKH GHVLUHG ORFDWLRQ IRU WKH KROH
then pull the switch trigger. Do not force the tool. Light
SUHVVXUH JLYHV EHVW UHVXOWV .HHS WKH WRRO LQ SRVLWLRQ
and prevent it from slipping away from the hole.
'R QRW DSSO\ PRUH SUHVVXUH ZKHQ WKH KROH EHFRPHV
clogged with chips or particles. Instead, run the tool at
DQ LGOH WKHQ UHPRYH WKH GULOO ELW SDUWLDOO\ IURP WKH KROH
%\ UHSHDWLQJ WKLV VHYHUDO WLPHV WKH KROH ZLOO EH FOHDQHG
RXW DQG QRUPDO GULOOLQJ PD\ EH UHVXPHG
Blow-out bulb
Optional accessory
Fig.13: 1. %ORZRXW EXOE
$IWHU GULOOLQJ WKH KROH XVH WKH EORZRXW EXOE WR FOHDQ WKH
dust out of the hole.
Drilling operation
)LUVW WXUQ WKH DGMXVWLQJ ULQJ VR WKDW WKH DUURZ SRLQWV WR
the marking. Then proceed as follows.
Drilling in wood
:KHQ GULOOLQJ LQ ZRRG WKH EHVW UHVXOWV DUH REWDLQHG
with wood drills equipped with a guide screw. The guide
VFUHZ PDNHV GULOOLQJ HDVLHU E\ SXOOLQJ WKH GULOO ELW LQWR
the workpiece.
Drilling in metal
7R SUHYHQW WKH GULOO ELW IURP VOLSSLQJ ZKHQ VWDUWLQJ D
hole, make an indentation with a center-punch and
KDPPHU DW WKH SRLQW WR EH GULOOHG 3ODFH WKH SRLQW RI WKH
GULOO ELW LQ WKH LQGHQWDWLRQ DQG VWDUW GULOOLQJ
9 ENGLISH
marking.
PDUNLQJ 7KH DGMXVWLQJ