Bosch PSB 500 RE Manual Original página 14

OBJ_BUCH-862-010.book Page 14 Tuesday, June 14, 2016 1:29 PM
14 | English
Impact Drill
Spindle collar dia.
Max. drilling dia.
– Concrete
– Steel
– Wood
– with extraction device mounted
Chuck clamping range
Weight according to EPTA-Procedure 01:2014
– with extraction device
– without extraction device
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Assembly
 Before any work on the machine itself, pull the mains
plug.
Dust Extraction (PSB 500 RA) (see figures A–F)
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
 Use the dust/chip extraction only when working con-
crete, brick and brickwork. Wood or plastic chips can
easily lead to clogging.
 WARNING Fire hazard! Do not work metallic materials
with the extraction device mounted. Hot metal chips can
ignite parts of the extraction device.
1 609 92A 1MY | (14.6.16)
PSB 500 RE PSB 500 RA
mm 43
mm 10
mm 8
mm 25
mm 13
mm 2 – 13
kg –
kg 1.6
/II
To achieve optimum extraction results, please observe the
following notes:
– Pay attention that the extraction device faces flush against
the workpiece or the wall. This also makes drilling at a right
angle easier.
– When using the extraction device, always work with the
maximum speed.
– After reaching the desired drilling depth, pull the drill bit
out of the drill hole first and then switch off the impact drill.
– Use the extraction device only with the filter element 17
mounted, as otherwise dust/chips could access the interi-
or of the power tool and cause damage.
– Check the condition of the filter element 17 regularly. Re-
place a damaged filter element immediately.
– The dust protection ring 19 can wear, especially when
working with large drill-bit diameters. Replace the dust
protection ring when worn/damaged.
Mounting the Extraction Device (see figure A)
Guide the extraction device 12 from the front toward the bot-
tom side of the impact drill. Pay attention that the extraction
device 12 faces flush against the casing and that it is locked.
Cleaning the Extraction Device (see figures B–D)
The dust collector 13 is sufficient for approx. 10 drillings with
a drilling diameter of 10 mm.
When the extraction force diminishes or when the level indi-
cator 14 is full, the dust collector 13 must be emptied. For
this, press on the riffled surface of the release button 16 and
take off the dust collector 13.
Empty and clean the dust collector 13. Clean the filter ele-
ment 17 by gently striking or tapping against it.
Check the filter element 17 for damage and replace it as re-
quired.
Press on the holder of the filter element 17 and pull it out. Re-
place the filter element 17 including the holder. When placing
on the holder again, make sure that the rubber gasket 18 is in-
serted.
Reattach the dust collector 13 again and lock it by pressing
against the smooth surface of the release button 16.
PSB 560 RE
43 43
10 10
8 8
25 25
13 13
2 – 13 2 – 13
1.8 –
– 1.6
/II /II
Bosch Power Tools