Tool Assembly - Milwaukee 9070-20 Manual Del Operador

To reduce the risk of injury, always unplug tool before attaching
or removing accessories or making adjustments. Use only specifi -
cally recommended accessories. Others may be hazardous.
Removing and Replacing Quik-Lok
9072-22, 9092-20 and 9096-20
MILWAUKEE's exclusive Quik-Lok
or substitution.
Fig. 1
1. To remove the Quik-Lok ® Cord, turn the cord nut 1/4 turn to the left and
pull it out.
2. To replace the Quik-Lok ® Cord, align the connector keyways and push
the connector in as far as it will go. Turn the cord nut 1/4 turn to the
right to lock.
Attaching and Removing the Tool Hanger (Fig. 2) Cat. No. 9092-20,
9096-20, or as an accessory
Fig. 2
Gear case
screws
1. To attach, remove the two top gear case screws (Fig. 2).
2. Place the ring through the tool hanger.
3. Position the tool hanger on the tool over the two gear case screw
holes.
4. Replace the two gear case screws. Hand tighten the screws.
5. To remove, reverse the procedure.
Use only sockets and other accessories specifi cally designed for
use on impact wrenches and drivers. Other sockets and acces-
sories might shatter or break causing injury.
Attaching and Removing Accessories (Fig. 3) Cat. No. 9071-20, 9075-20
This impact wrench is intended only for use with sockets designed for impact
wrenches and that have a 1/2" square drive (3/4" square drive for Cat. No.
9075-20). Other sockets could shatter or break, causing injury.

TOOL ASSEMBLY

WARNING
®
Cords (Fig. 1) Cat. No. 9072-20,
® Cords provide instant fi eld replacement
Ring
Tool
hanger
WARNING
Fig. 3
Drive shank
1. To attach a socket or other accessory, push the accessory onto the
drive shank until it snaps into place.
2. To remove the accessory, pull it off the drive shank.
Attaching and Removing Accessories (Fig. 4) Cat. No. 9070-20, 9072-
20, 9072-22
These impact wrenches are intended only for use with sockets designed
for impact wrenches and that have a 1/2" square drive. Other sockets could
shatter or break, causing injury.
Fig. 4
Detent pin
1. To attach a socket or other accessory, align the hole in the accessory
with the detent pin on the drive shank. Hold the detent pin in while
pushing the socket onto the drive shank. The detent pin will snap into
place in the hole to secure the socket.
2. To remove the accessory, insert a nail or other thin object into the hole
in the accessory and press the detent pin in. Pull the accessory off the
drive shank.
Attaching and Removing Accessories (Fig. 5) Cat. No. 9092-20, 9096-20,
or other Impact Wrenches using the Quick Change 1/2" Square Drive
to 7/16" Hex Adapter
Cat. No. 9092-20 and accessory Cat. No. 48-66-0061 are intended for use
with drill bits and adapters with a 7/16" Hex Quick Change shank. Cat. No.
9096-20 is intended for use with drill bits and adapters with a 5/8" Hex Quick
Change shank. Both Hex Quick Change shanks have a ball-retainer groove.
They are not intended for use with Hex Shank Bit Extensions.
Fig. 5
Ball-retainer
groove
1. To attach an accessory, pull the chuck collar forward and insert the ac-
cessory shank. Release the collar. It may be necessary to pull the bit
out slightly to engage the holding mechanism.
2. To remove the accessory, pull the chuck collar forward and remove the
accessory. Release the collar.
Drive shank
Open (Release)
Closed (Locked)
page 5