Technical Data - IKRA THS 500 Pro Instrucciones De Manejo

Electric telescoping hedge trimmer

Technical data

Model
Operating-voltage----------------- -------------V~----- 230-
Nominal-frequency----------------------------------Hz---------50-
Nominal-consumption-----------------------------W----
Cutting-motion----------------------- --------------rpm-
Maximum-cutting-length--------- --------------mm-
Maximum-cutting-diameter----------------------mm-------22
Angle-at-which-the-motor-can-be-set--------------------0°-to-135°
Tool-length----------------------------------------------mm--------2015---2432-
Weight-without-the-cable-------------------------kg------
Noise-level-
(EN-60745-2-15)
Vibration-
(EN-60745-2-15)
Protection-class-II/DIN-EN-60745/VDE-0740------ - -
The-specified-vibration-emissions-value-is-measured-in-accordance-with-EN-60745.-This-can-be-used-for-any-other-
hedge-trimmer-with-the-same-design-and-type-of-power-supply.
The-specified-vibration-emissions-value-limits-the-working-time.-Stop-working-if-you-notice-a-tingling-sensation-or-a-
discolouration-(white)-of-the-fingers.
WARNING: When-in-operation,-the-tool's-actual-vibration-emissions-value-can-deviate-from-the-specified-value-de-
pending-on-how-the-tool-is-used,-as-in-the-following-examples-or-because-it-is-used-in-another-way:
- - How-the-tool-is-being-used-and-which-materials-are-being-cut.
- - The-tool-is-well-maintained-and-in-good-working-order.-The-correct-accessories-are-being-used-and-care-has-been-
taken-to-make-sure-they-are-sharp-and-in-good-working-order.
- - How-secure-the-hand-grip-is-and-whether-anti-vibration-accessories-are-being-used.
- - Whether-the-tool-is-being-used-in-accordance-with-its-design-and-as-specified-in-these-instructions.
- - The-tool-can-cause-hand-arm-vibration-syndrome-symptoms-if-it-is-not-used-properly.
WARNING: To-make-sure,-an-assessment-should-be-made-of-the-strain-exerted-when-the-tool-is-in-use,-for-example-
when-the-tool-is-switched-off-or-is-idling.-This-will-make-it-possible-to-significantly-reduce-the-strain-exerted-during-the-
entire-time-the-tool-is-in-use.
Minimise-your-risks-if-the-tool-vibrates.
Take-care-of-the-tool-as-specified-in-these-instructions-and-make-sure-the-tool-is-properly-lubricated-(if-necessary).
If- the- temperature- is- 10°C- or- less,- do- not- use- the- tools.- Prepare- a- work- schedule- so- that- work- is- distributed- over-
several-days-when-using-tools-that-exert-high-vibrations.
Noise-emission-information-in-accordance-with-the-German-Product-Safety-Act-(ProdSG)-and-the-EC-Machine-Direc-
tive:-the-noise-pressure-level-at-the-place-of-work-can-exceed-80-dB(A).-In-such-cases-the-operator-will-require-noise-
protection-(e.g.-wearing-of-ear-protectors).
Attention: Noise protection! Please-observe-the-local-regulations-when-operating-your-device.
----------------------dB-(A)---83----
-----------------------m/s
----------
2
THS 500 Pro (Ikramogatec)
500- -
3300-
515- -
4,1-
K-3,0-dB(A) ------
2
2,5---
K 1,5 m/s
GB-4
-