Functional Description - Milwaukee M18 FUEL 2762-059 Manual De Instrucciones

FUNCTIONAL DESCRIPTION

1. 1/2" Square drive anvil with pin
2. LED
1
2
3
5
4
3. Control switch
4. Trigger
5. 2-Mode drive control
6. Handle
7. 1/2" Square drive anvil with ring (2763-059)
8. 3/4" Square drive anvil with ring (2764-059)
9. 7/16" Hex Quick Connect (2765-059)
SPECIFICATIONS
Volts .............................................................. 18 DC
Battery Type .................................................M18™
Charger Type ................................................M18™
Cat. No. ................................................... 2762-059
Anvil type ........................................1/2" Square-Pin
RPM ...................... Mode 1 .......... Speed .....0-1200
Mode 2 .......... Speed .... 0-1700
IPM ....................... Mode 1 ........Impacts ........1700
Mode 2 ........Impacts ........2300
Cat. No. ................................................... 2763-059
Anvil type ..................................... 1/2" Square-Ring
RPM ...................... Mode 1 .......... Speed .......0-450
Mode 2 .......... Speed .... 0-1700
IPM ....................... Mode 1 ........Impacts ..........450
Mode 2 ........Impacts ........2300
Cat. No. ................................................... 2764-059
Anvil type ..................................... 3/4" Square-Ring
RPM ...................... Mode 1 .......... Speed .....0-1200
Mode 2 .......... Speed .... 0-1700
IPM ....................... Mode 1 ........Impacts ........1700
Mode 2 ........Impacts ........2300
Cat. No. ................................................... 2765-059
Anvil type ................................................. 7/16" Hex
RPM ...................... Mode 1 .......... Speed .....0-1200
Mode 2 .......... Speed .... 0-1700
IPM ....................... Mode 1 ........Impacts ........1700
Mode 2 ........Impacts ........2300
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Impacts per Minute under Load (IPM)
Seal of Electrical Security
Read operator's manual
Wear hearing protection
Wear eye protection
(2762-059)
cific charging instructions, read the operator's
manual supplied with your charger and battery.
To remove the battery, push in the release buttons
7
and pull the battery pack away from the tool.
6
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
8
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
use on impact wrenches and drivers. Other
sockets and accessories might shatter or break
9
causing injury.
1. Use only the appropriate size Square Drive Sockets.
2. To attach a socket, align the hole in the accessory
3. To remove the socket, insert a nail or other thin
1. Use only the appropriate size Square Drive Sockets.
2. To attach a socket, align the accessory with the
3. To remove the accessory, pull the accessory off
7/16" Hex Impact Wrench
(Cat. No. 2765-059)
This impact driver is intended for use
with drill and driver bits.
1. To attach an accessory, press the
2. To remove the accessory, pull out
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear safety
goggles or glasses with side shields.
The drive control button is used to adjust the torque,
rotation speed (RPM), and impact speed (IPM) for the
application (see Specifications chart for RPM and IPM).
To select the drive control mode:
1. Pull and release the trigger to turn on the tool. The
2. Press the drive control button
11
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
Removing/Inserting the Battery
Always remove battery pack before
WARNING
changing or removing accesso-
Use only sockets and other acces-
WARNING
sories specifically designed for
Attaching and Removing Accessories
1/2" Impact Wrench with Pin
(Cat. No. 2762-059)
with the detent pin on the anvil. Hold the detent
pin in while pushing the socket onto the anvil.
The detent pin will snap into place in the hole to
secure the socket.
object into the hole in the accessory and press
in the detent pin. Pull the accessory off the anvil.
1/2" and 3/4" Impact Wrench with Ring
(Cat. No. 2763-059, 2764-059)
anvil and push it firmly over the retaining ring.
the anvil.
shank into the hex drive chuck.
the ring and remove the accessory.
Release the ring.
OPERATION
Always remove battery pack before
WARNING
changing or removing accesso-
Using the Drive Control
current mode indicator is lit.
the 2 modes. When the desired mode indicator is
lit, begin work.
to cycle through