Makita DLS714 Manual De Instrucciones página 21

Sierra de inglete inalámbrica
Ocultar thumbs Ver también para DLS714:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 87
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
Fig.45: 1. 52/38° type crown molding 2. 45° type
crown molding 3. 45° type cove molding
Fig.46: 1. Inside corner 2. Outside corner
Fig.47: 1. Inside corner 2. Outside corner
Measuring
workpiece according to it. Always make sure that width
of the workpiece's wall contact edge is the same as wall
length.
Fig.48: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
Always use several pieces for test cuts to check the
saw angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
Fig.49: 1. Inside corner 2. Outside corner
Table (A)
Molding
Bevel angle
position
52/38°
in the
type
For
(a)
Left
inside
33.9°
corner
(b)
For
(c)
outside
(d)
corner
Table (B)
Molding
position in
For inside
(a)
corner
(b)
For outside
(c)
corner
(d)
Miter angle
45° type
52/38°
45° type
type
Left 30°
Right
Right
31.6°
35.3°
Left
Left
31.6°
35.3°
Right
Right
31.6°
35.3°
Molding
Finished
edge against
piece
guide fence
Ceiling
Finished
contact edge
piece will be
should be
on the Left
against guide
side of blade.
fence.
Wall contact
edge should
Finished
be against
piece will be
guide fence.
on the Right
Ceiling
side of blade.
contact edge
should be
against guide
fence.
Example:
In the case of cutting 52/38° type crown molding for
Tilt and secure bevel angle setting to 33.9° LEFT.
RIGHT.
Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on the
saw.
the LEFT side of the blade after the cut has been
made.
Wood facing
WARNING:
Use screws to attach the wood
facing to the guide fence. The screws should be
installed so that the screw heads are below the
surface of the wood facing so that they will not
interfere with the positioning of the material being
cut. Misalignment of the material being cut can case
unexpected movement during the cutting operation
which may result in a loss of control and serious
CAUTION:
Use the straight wood of even
thickness as the wood facing.
Use of wood facing helps to assure splinter-free cuts
in workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence.
gested wood facing.
15mm (5/8")
35mm
(1-3/8")
92mm
1
(3-5/8")
Fig.50
Fig.50: 1. Holes
NOTICE:
When the wood facing is attached, do
not turn the turn base with the handle lowered.
The blade and/or the wood facing will be damaged.
21 ENGLISH
420mm (16-1/2")
50mm-60mm
(2"-2-3/8")
27mm (1-1/16")
1
100mm
70mm
85mm
(3-15/16")
(2-3/4")
(3-3/8")
-

Publicidad

Tabla de contenido
loading

Tabla de contenido