Switch Action; Adjusting Depth Of Cut; Bevel Cutting - Makita DHS782 Manual De Instrucciones

Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.9: 1. Indicator lamps 2. Check button
3UHVV WKH FKHFN EXWWRQ RQ WKH EDWWHU\ FDUWULGJH WR LQGLFDWH WKH UHPDLQ-
LQJ EDWWHU\ FDSDFLW\ 7KH LQGLFDWRU ODPSV OLJKW XS IRU D IHZ VHFRQGV
Indicator lamps
Lighted Off
NOTE: Depending on the conditions of use and the
DPELHQW WHPSHUDWXUH WKH LQGLFDWLRQ PD\ GLIIHU VOLJKWO\
IURP WKH DFWXDO FDSDFLW\

Switch action

WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A switch with
D QHJDWHG ORFNRII EXWWRQ PD\ UHVXOW LQ XQLQWHQWLRQDO
RSHUDWLRQ DQG VHULRXV SHUVRQDO LQMXU\
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button. A switch in need of repair
PD\ UHVXOW LQ XQLQWHQWLRQDO RSHUDWLRQ DQG VHULRXV
SHUVRQDO LQMXU\ 5HWXUQ WRRO WR D 0DNLWD VHUYLFH FHQWHU
for proper repairs BEFORE further usage.
7R SUHYHQW WKH VZLWFK WULJJHU IURP EHLQJ DFFLGHQWDOO\ SXOOHG D ORFN
off button is provided. To start the tool, depress the lock-off button
and pull the switch trigger. Release the switch trigger to stop.
Fig.10: 1. Switch trigger 2. Lock-off button
NOTICE:
Do not pull the switch trigger hard
without pressing in the lock-off button. This can
cause switch breakage.
CAUTION:
The tool starts to brake the cir-
cular saw blade rotation immediately after you
UHOHDVH WKH VZLWFK WULJJHU +ROG WKH WRRO ¿UPO\ WR
respond the reaction of the brake when releasing
the switch trigger. Sudden reaction can drop the tool
RII \RXU KDQG DQG FDQ FDXVH D SHUVRQDO LQMXU\
Automatic speed change function
This tool has "high speed mode" and "high torque
mode".
7KH WRRO DXWRPDWLFDOO\ FKDQJHV WKH RSHUDWLRQ PRGH
GHSHQGLQJ RQ WKH ZRUN ORDG :KHQ WKH ZRUN ORDG LV ORZ
the tool will run in the "high speed mode" for quicker
FXWWLQJ RSHUDWLRQ :KHQ WKH ZRUN ORDG LV KLJK WKH WRRO
Remaining
capacity will run in the "high torque mode" for powerful cutting
operation.
Blinking
75% to 100%
The mode indicator lights up in green when the tool is
running in "high torque mode".
If the tool is operated with excessive load, the mode
50% to 75%
indicator will blink in green. The mode indicator stops
EOLQNLQJ DQG WKHQ OLJKWV XS RU WXUQV RII LI \RX UHGXFH WKH
25% to 50%
load on the tool.
0% to 25%
Charge the
EDWWHU\
7KH EDWWHU\
PD\ KDYH
malfunctioned.

Adjusting depth of cut

Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
E\ WLJKWHQLQJ WKH OHYHU
For cleaner, safer cuts, set cut depth so that no more
WKDQ RQH EODGH WRRWK SURMHFWV EHORZ ZRUNSLHFH 8VLQJ
proper cut depth helps to reduce potential for danger-
RXV .,&.%$&.6 ZKLFK FDQ FDXVH SHUVRQDO LQMXU\

Bevel cutting

Loosen the clamping screws. Set for the desired angle
E\ WLOWLQJ DFFRUGLQJO\ WKHQ WLJKWHQ WKH FODPSLQJ VFUHZV
VHFXUHO\
8VH WKH VWRSSHU ZKHQ \RX GR SUHFLVH ƒ DQJOH FXWWLQJ
)XOO\ WXUQ WKH VWRSSHU DV LOOXVWUDWHG GHSHQGLQJ RQ ƒ 
45° bevel cut or 0° - 48° bevel cut.
15 ENGLISH
Fig.11: 1. Mode indicator
Mode indicator status
On Off
CAUTION:
After adjusting the depth of cut,
always tighten the lever securely.
Fig.12: 1. Lever
CAUTION:
After adjusting the bevel angle,
always tighten the clamping screws securely.
Fig.13: 1. Clamping screw
Fig.14: 1. Stopper
Operation
mode
Blinking
High speed
mode
High torque
mode
Overload
alert