Optional Accessories - Makita DHS782 Manual De Instrucciones

MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system. A
GLUW\ JXDUGLQJ V\VWHP PD\ OLPLW WKH SURSHU RSHUDWLRQ ZKLFK
FRXOG UHVXOW LQ VHULRXV SHUVRQDO LQMXU\ 7KH PRVW HIIHFWLYH
ZD\ WR DFFRPSOLVK WKLV FOHDQLQJ LV ZLWK FRPSUHVVHG DLU If
the dust is being blown out of the guards, be sure the
proper eye and breathing protection is used.
CAUTION:
After each use, wipe off the saw
dust on the tool. )LQH VDZ GXVW PD\ FRPH LQVLGH WKH
WRRO DQG FDXVH PDOIXQFWLRQ RU D ¿UH
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
UHSDLUV DQ\ RWKHU PDLQWHQDQFH RU DGMXVWPHQW VKRXOG
EH SHUIRUPHG E\ 0DNLWD $XWKRUL]HG RU )DFWRU\ 6HUYLFH
&HQWHUV DOZD\V XVLQJ 0DNLWD UHSODFHPHQW SDUWV
Adjusting 0°-cut or 45°-cut accuracy
7KLV DGMXVWPHQW KDV EHHQ PDGH DW WKH IDFWRU\ %XW LI LW LV
RII \RX FDQ DGMXVW LW DV WKH IROORZLQJ SURFHGXUH
1. Loosen the clamping screws on the front and rear
of the tool so that the bevel angle can be changed. Set
WKH VWRSSHU WR ƒ  ƒ EHYHO DQJOH SRVLWLRQ LI \RX DUH
JRLQJ WR DGMXVW ƒFXW DFFXUDF\
Fig.47: 1. Stopper
2. Make the base perpendicular or 45° to the circular saw
EODGH XVLQJ D WULDQJXODU UXOH E\ WXUQLQJ WKH DGMXVWLQJ VFUHZ ZLWK D
KH[ ZUHQFK <RX FDQ DOVR XVH D VTXDUH UXOH WR DGMXVW ƒ DQJOH
Fig.48: 1. Triangular rule
Fig.49: 1. $GMXVWLQJ VFUHZ IRU ƒ DQJOH 2. $GMXVWLQJ
screw for 45° angle
3. Tighten the clamping screws and then make a test
cut to check if desired angle is obtained.
Adjusting the parallelism
CAUTION:
Keep the parallelism accurate.
2WKHUZLVH WKH FLUFXODU VDZ EODGH PD\ ELWH LQWR WKH
JXLGH UDLO DQG WKH GDPDJHG JXLGH UDLO PD\ FDXVH DQ
LQMXU\
7KLV DGMXVWPHQW KDV EHHQ PDGH DW WKH IDFWRU\ %XW LI LW LV
RII \RX FDQ DGMXVW LW DV WKH IROORZLQJ SURFHGXUH
1. Set the tool to the maximum cutting depth.
2. Make sure all levers and screws are tightened.
3. /RRVHQ WKH VFUHZV VKRZQ LQ WKH ¿JXUH
4. :KLOH RSHQLQJ WKH ORZHU JXDUG PRYH WKH UHDU RI
the base so that the distance A and B becomes equal.
Fig.50: 1. Screw 2. Base
5. Tighten the screws and make a test cut to check
the parallelism.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
VSHFL¿HG LQ WKLV PDQXDO 7KH XVH RI DQ\ RWKHU
accessories or attachments might present a risk of
LQMXU\ WR SHUVRQV 2QO\ XVH DFFHVVRU\ RU DWWDFKPHQW
for its stated purpose.
,I \RX QHHG DQ\ DVVLVWDQFH IRU PRUH GHWDLOV UHJDUG-
LQJ WKHVH DFFHVVRULHV DVN \RXU ORFDO 0DNLWD 6HUYLFH
Center.
• Circular saw blade
‡ 5LS IHQFH *XLGH UXOH
• Hook
• Guide rail
• Bevel guide
• Clamp
• Sheet
• Rubber sheet
• Position sheet
‡ 'XVW QR]]OH
• Hex wrench
‡ :LUHOHVV XQLW IRU '+6
‡ 0DNLWD JHQXLQH EDWWHU\ DQG FKDUJHU
NOTE: 6RPH LWHPV LQ WKH OLVW PD\ EH LQFOXGHG LQ WKH
WRRO SDFNDJH DV VWDQGDUG DFFHVVRULHV 7KH\ PD\
GLIIHU IURP FRXQWU\ WR FRXQWU\
22 ENGLISH