Standard Accessories; Prior To Operation - HIKOKI C 9SA3 Instrucciones De Manejo

English
PRECAUTIONS ON USING CIRCULAR SAW
1. Use only blade diameter specifi ed on the machine.
2. Do not use any abrasive wheel.
3. Do not use saw blades which are deformed or cracked.
4. Do not use saw blades made of high speed steel.
5. Do not use saw blades which do not comply with the
characteristics specifi ed in these instructions.
6. Do not stop the saw blades by lateral pressure on the
disc.
7. Always keep the saw blades sharp.
8. Ensure that the lower guard smoothly and freely.
SPECIFICATIONS
Model
Voltage (by areas)*
Cutting Depth
Power Input*
No-load speed
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Saw Blade (Dia. 235 mm) ............................................1
(2) Hex. bar wrench ............................................................1
(3) Guide ..........................................................................1
(4) Wing-bolt ......................................................................1
(5) Lock spring ...................................................................1
(6) Lever (short type) ..........................................................1
(7) Dust collector ................................................................1
(8) Side handle ...................................................................1
(9) Screw (M6 × 20)............................................................2
Standard accessories are subject to change without notice.
APPLICATION
Cutting various types of wood.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Before the tool is plugged in to the receptacle, ensure
that the power switch is in the OFF position. If the plug
is connected to a receptacle while the power switch is
in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prepare a wooden workbench (Fig. 3)
Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
7
9. Never use the circular saw with its lower guard fi xed in
10. Ensure that the retraction mechanism of the guard
11. Never operate the circular saw with the saw blade turned
12. Ensure that the material is free of foreign matters such as
13. For model C9SA3, the saw blades should be 235 mm.
14. Disconnect the plug from the receptacle before carrying
15. Do not use the tool with only the blower function. (Fig. 2)
90°
45°
5. When using the side handle (Fig. 4)
CAUTION
6. Using the cord holder (Fig. 5)
ADJUSTING THE SAW PRIOR TO USE
1. Adjusting the cutting depth
2. Adjusting the angle of inclination
3. Regulating the guide (Fig. 8)
4. Adjusting the guide piece
the open position.
system operates correctly.
upward or to the side.
nails.
out any adjustment, servicing or maintenance.
C9SA3
(127 V, 220 V)
86 mm
65 mm
1800 W (127 V), 2000 W (220 V)
5200 min (/min)
-1
7.0 kg
Securely attach the side handle to the base with the two
screws (M6 × 20) when using the side handle.
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
Using the cord holder, the cord can be guided toward the
rear of the product, as shown in the fi gure.
If the cord is interfering during operation, hook it into the
cord holder and change its angle.
As shown in Fig. 6, hold the handle with one hand while
loosening the knob with the other.
The cutting depth can be adjusted by moving the base
to the desired position. In such manner adjust the cutting
depth and then securely retighten the knob.
As shown in Fig. 7 (A), Fig. 7 (B) by loosening the wing-
nut on the incline gauge and the wing-bolt on the base,
the saw blade may be inclined to a maximum angle of
45° in relation to the base. After having completed the
adjustment, reconfi rm that the wing-nut and the wing-bolt
are fi rmly tightened.
The cutting position can be regulated by moving the
guide to the left or right after loosening its wingbolt. The
guide may be mounted on either the right or left side of
the tool.
On the circular saw, it is possible to make fi ne adjustment
of the fi xing position of the guide piece, where the saw
blade and the premarked line are to be aligned.
When the saw is shipped from the factory, the linear
portion of a front scale on the guide piece is aligned with
the central position of the saw blade (Fig. 9).