HIKOKI CE 18DSL Instrucciones De Manejo página 6

English
● Regarding the temperatures and charging time of the battery.
The temperatures and charging time will become as shown in Table 2.
Battery
Charging voltage
Weight
Temperatures at which the battery can be recharged
Charging time for battery capacity, approx.(At 20oC)
1.3 Ah
1.5 Ah
2.0 Ah
2.5 Ah
3.0 Ah
4.0 Ah
5.0 Ah
Number of battery cells
*1 AC power supply / DC 12 V (in-car) power supply
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
<UC18YML2>
Especially, using a DC 12 V in-car power source may
require longer recharging time at high temperatures.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger's power cord from the
receptacle or cigarette lighter socket.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used,
the pilot lamp of the charger lights up green or lights
for 1 second, does not light for 0.5 seconds (off for
0.5 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about 3
seconds to confi rm that the battery being charged with
charger is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
○ Check the voltage of the in-car power source when
the pilot lamp fl ickers in green (every 0.2 seconds)
continuously. (UC18YML2)
If the voltage is 12 V or lower, it indicates that the car
battery has weakened and cannot be charged.
○ If the pilot lamp does not blink in red (every second) even
though the charger cord or cigarette lighter connecting
plug is connected to the power, it indicates that the
protection circuit of the charger may be activated.
Remove the cord or plug from the power and then connect
it again after 30 seconds or so. If this does not cause the
pilot lamp to blink in red (every second), please take the
charger to the HiKOKI Authorized Service Center.
Table 2
Charger
UC18YFSL
V
kg 0.5
min. 20
min. 22
min. 30
min. 35
min. 45
min. 60
min. 75
MOUNTING AND OPERATION
Removing and inserting the battery
Charging
Adjusting the horizontal gap
between the shearing blades
Switch operation
Remaining battery indicator
Cutting plates
Blade replacement
Selecting accessories
*1. Adjusting the horizontal gap between the shearing
blades ⓑ (see Fig. 3)
Adjust the horizontal gap between the shearing blades (A
in Fig. 3) at approximately 1/10 the steel plate thickness
to be sheared, according to the following procedures.
(1) Loosen the hexagonal socket bolts ⓒ fastening the
stationary blade. Loosen the M4 lock nut ⓓ, and
push back the M4 slotted set screws ⓔ slightly.
(2) From the supplied thickness gauges ⓕ, select one
that is 1/10 the thickness of the panel to be cut.
Thickness of each thickness gauge ⓕ is marked
thereon. Insert the gauge ⓕ in between the blades,
then tighten the hexagonal socket bolts ⓒ very
loosely. Next, use a screwdriver to turn the M4
slotted set screws ⓔ to position the stationary blade
until it hits the thickness gauge ⓕ.
(3) If the space between blades is larger than the
thickness of the panel to be cut, there will be burrs for
a less than clean cut.
If the space between blades is too narrow, cutting
speed will be aff ected. For cutting in a curved line,
making the space a little bigger will make the cutting
easier.
(4) After adjustment, tighten the M4 nuts ⓓ securely so
they will not loosen during operation.
(5) Securely tighten the hexagonal socket bolts ⓒ
fastening the stationary blade.
*2. Cutting (see Fig. 6)
CAUTION
○ Do not attempt to cut panels of thicknesses that are
beyond the capability of the hand shear. Doing so will
result in premature breakage of the hand shear.
6
UC18YML2
(AC/DC)*
14.4 – 18
0oC – 50oC
20 / 50
22 / 60
30 / 80
35 / 100
45 / 120
60 / 160
75 / 200
4 – 10
Action Figure
*1
*2
1
0.7
Page
1 158
2 158
3
158
4 159
5 159
6
159
7
159
― 160