Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TH-US 240 Manual De Instrucciones Original

the fl ange (C) and replace the grinding wheel (5).
The grinding wheel is mounted with the help of a
rag. Mount the fl ange (C) on the shaft and screw
on the nut (D) hand-tight (Fig. 10). To tighten the
nut (D), hold the grinding wheel (5) with a rag and
tighten the nut (D) (Fig. 10).
5.5. Changing the grinding/sanding belt (Fig.
1/11)
•
Undo the 3 screws (14) and remove the side
safety guard. Slacken the clamp screw for the
top belt roller (12) by a few turns.
•
Push the clamping lever (13) downwards and
pull the grinding/sanding belt off the rollers.
•
Place the new grinding/sanding belt (11) in
the center of the top and bottom rollers and
release the clamping lever (13).
•
Now tighten the clamp screw (12) and fit the
side safety guard.
•
With the belt guidance adjustment screw (15)
on the side you can adjust the belt run by
slackening the nut on the adjustment screw
of the belt guidance (15) and adjusting the
precision of the belt run with a screwdriver.
Pecise adjustment of the belt run is best done
by turning the grinding/sanding belt by hand.
Once you have adjusted the belt run, retigh-
ten the nut with a ring spanner.
6. Operation
6.1 On/Off switch (1)
•
To switch on the equipment set the On/Off
switch (1) to position 1.
•
Move the On/Off switch (1) to position 0 to
switch off the equipment.
After switching on, wait for the equipment to reach
its maximum speed of rotation. Only then should
you begin with the grinding.
6.2 Grinding
•
Place the workpiece onto the workpiece
support (7) and slowly guide the workpiece
towards the grinding wheel (5) at the desired
angle to the point where workpiece and grin-
ding wheel make contact.
•
Move the workpiece slightly back and forth to
produce an optimal grinding result. This way
the grinding wheel (5) will be evenly worn. Al-
low the workpiece to cool down occasionally.
Anl_SA_TH_US_240_SPK8.indb 18 Anl_SA_TH_US_240_SPK8.indb 18
GB
6.3 Grinding/sanding with the belt
•
Always hold the workpiece firmly during grin-
ding/sanding.
•
Do not exert excessive pressure.
•
The workpiece should be moved to and fro
on the belt as you grind/sand it to prevent the
paper wearing on one side.
•
Important! Pieces of wood should always be
sanded with the grain to prevent them split-
ting.
Important!
If the grinding wheel or the grinding/sanding belt
becomes jammed during operation, please re-
move the workpiece until the tool reaches its top
speed again.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 18 -
22.02.2018 11:06:01 22.02.2018 11:06:01