Terminal Description - BFT BOTTICELLI VENERE Instrucciones De Uso

WARNING: the anti-tear rubber element must never be completely
compressed. Scrupulously check that the rubber does not become
totally compressed during operation.
6) ELECTRICAL INSTALLATION SET-UP (Fig.16)
M)
Ft) Transmitter photocell
Fr)
T) 1-2-4 channel transmitter.
to reach the motor unit, keeping the mains voltage connections clearly
the appropriate cable holder (fig. 8 ref. 5P1).
Proceed to connection following the indications given in the wiring diagram.
The cables for connecting the accessories must be protected by a raceway
(fig. 8 ref. 5C1).
7) VENERE Control panel (Fig.17)
Supply to accessories: ..................................................24V~
.............................................................24V~
Torque limiter setting:..............................................on closing and opening
Blinker connection:..............................................................24V~
Service light switching-on time:..............................................................90s
Incorporated rolling-code radio receiver:..................frequency 433.92 MHz
Coding:.......................................................................rolling-code algorithm
No. combinations:...........................................................................4 milliard
Slow-down distance:................closing: ~24 cm ............... opening: ~24 cm
Fuses:......................................................................................see figure 17
7.1) Terminal board connections (Fig.17)
WARNINGS - For wiring and installation operations, refer to the current
standards and good technical principles.
cally separate from the low voltage wires, or else they must be provided with
adequate additional insulation of at least 1mm.
TERMINAL DESCRIPTION
JP6
transformer wiring
JP7 motor wiring
1-2
(1: BRAID. 2: SIGNAL)
3-4
3-5
3-6
inserted.
3-7
8-9 24 V~
10-11 24V~
or other devices
12-13 24V~
photocell transmitters.
7.2) LED (Fig.17)
The led functions are as follows:
"RADIO":Incorporated radio-receiver led.
"SET": Limit device setting led
7.3) DIP-SWITCH SELECTION (Fig.17)
DIP1) IBL
DIP2) TEST PHOT
INSTALLATION MANUAL
7.4) TRIMMER SETTING (Fig.17)
TCA
Sets the automatic closing time, after which the gate closes automatically
is disabled.
OPENING TORQUE
Sets the ampere-stop sensitivity on opening.
CLOSING TORQUE
Sets the ampere-stop sensitivity on closing.
NOTE: In case of obstacle detection, the Ampere-stop function halts
the leaf movement, reverses the motion for 1 sec. and stays in the
STOP state.
WARNING: check that the impact force value measured at the
points established by the EN 12445 standard is lower than that
specified in the EN 12453 standard.
Incorrect sensitivity setting can cause injuries to persons or ani-
mals, or damage to things.
7.5) BUTTONS
"UP":
"DOWN": limit device setting and closing command.
"OK":
8) LIMIT DEVICE SETTING (Fig.18)
"SET" led blinks to indicate that the limit device setting is activated.
button in order to memorise the limit device closing position. The "SET"
led confirms data storage by blinking for 1 second.
-
"SET" led confirms data storage by blinking for 1 second and then lits up
again.
NOTE 1: These manoeuvres are carried out in "hold-to-run" mode at reduced
speed and with no safety devices activated.
NOTE 2: In case of errors, the "SET" led remains off on for 5 seconds.
9) OPENING / CLOSING TORQUE AUTOSETTING (Fig.19)
for 5 seconds.
2) The "SET" led blinks rapidly and the leaf starts to open until it reaches
the opening end-of-stroke.
3) 3 second down time.
4) The "SET" led blinks rapidly and the leaf starts to close until it reaches
the closing end-of-stroke
so as to obtain the desired sensitivity to the obstacle.
Any input activation (START, RADIO TRANSMITTER, STOP, PHOTOCELL)
during autosetting will annul the autoset in progress.
10) INTEGRATED RECEIVER
Transmitter versions which can be used:
10.1)ANTENNA INSTALLATION
Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
reception. In case of insufficient transmitter range, move the antenna to a
more suitable position.
10.2) MANUAL TRANSMITTER PROGRAMMING (Fig.20)
blinking again.
4) To memorise another transmitter, repeat steps 2) and 3).
of the torque will be performed by keeping this button pressed
for 5 seconds (Fig.19).
radio programming.
ENGLISH
.
13
BOTTICELLI VENERE -