Handpiece; Safety Precautions; Set-Up And Assembly - coltene/whaledent Coltolux LED Manual Del Usuario

86768G Quark_Translated.2.qxd
Owner's Guide Owner's Guide
Caution: Federal law restricts this
device to sale by or on the order of a
dentist.
Congratulations...
...on your purchase of the Coltolux
LED
Curing Light. Coltolux
designed for intra- and extra- oral
polymerization of visible-light-cured
dental materials with Camphorquinone
(CQ) Photoinitiators. See Figure 1 and
Figure 2 for component recognition.
Fig. 1.
a. Handpiece
b. Handpiece Charger Base
c. Activation Button
Fig. 2.
d. Voltage/Serial Number Label
e. Power Cord with Power Supply
f. Plug Adapters (Export Only)
g. Screwdriver (Export Only)
h. Test Block
i. Light Shields
j. Barrier Sleeves
k. Light Lenses
Please take special note of the
safety precautions below.
I. SAFETY PRECAUTIONS
A. Observe the following
precautionary procedures before
and whenever using the
®
Coltolux LED Curing Light:
CAUTION: Before connecting,
read all instructions.
CAUTION: Light output
from this unit, potentially
2
over 1000 mW/cm , may be a
significant increase compared
to other polymerization devices;
therefore, when using this
curing light:
8/14/06 9:23 AM
• Determine curing time of your
material using the enclosed
test block.
• Adjust curing techniques in
accordance with the increased
®
energy.
LED
®
is
WARNING: Do not substitute
the light lens from other curing
lights. Use only the light lens
supplied for this unit. Never use
components not designed for use
with this device since this may
impair performance. Do not
refrigerate or put in freezer
to cool.
CAUTION: Persons having
a history of photosensitive
reactions or who are using
photosensitizing drugs should
not be exposed to light from
this unit.
B. All high intensity lights may cause
retinal damage with prolonged
exposure to the eyes, therefore
we urge you observe these
cautionary statements:
CAUTION: Never look directly
into the light emitted from the
light lens or reflected from tooth
or other surfaces.
• Always use light shields (Cat.
No. C7944) available for light
curing or use eye protection
goggles (Cat. No. C7988) that
block light in the blue spectral
range. Sunglasses are not
adequate protection.
• A barrier sleeve should be
used for every patient (Cat. No.
C7597). Slide the barrier sleeve
over the handpiece and light
shield.
• Before each use, inspect the light
lens (Section VIII) .
Page 3
• Patients, operators and dental
CAUTION: The red indicator light
on the charger base indicates a
warning that the battery may not
have sufficient charge for proper
curing operation and that action
must be taken to charge the battery.
II. UNPACKING
• Before unpacking, examine the
• Open carton and carefully
III. SET-UP AND ASSEMBLY
• Coltolux
Page 3 Page 3
technicians should always use
proper eye protection.
carton for external damage, and
if severe, contact your
shipper/carrier.
remove the unit and accessories.
Make sure supply voltage is
within the range specified on the
power supply (Fig. 3) . If not, do
not operate this unit; contact your
dealer or Coltène/Whaledent Inc.
®
LED is designed as a
cordless handpiece unit with a
separate charger base. Place the
charger base on a smooth flat
surface in an area that is dry and
free of dust, is convenient and has
an outlet within easy reach of the
supplied power cord. Export units
include additional plug adapters.
Install the appropriate plug adapter
onto the power supply (Fig. 2). To
change the plug adapter, remove
screw, slide existing plug adapter out
of power pack and replace with
desired plug adapter, insert screw
and tighten securely (Fig. 4).
Please Note:Additional plug
adapters are not supplied for
Australian and New Zealand
markets. Plug the power cord into
the wall outlet and then into the
charger base. A green light on the
charger base indicates power is
available to charge the handpiece.