Technical Data - AEG STEP 70 Instrucciones De Uso

TECHNICAL DATA

Nominal power output .............................................................
Rated output ............................................................................
Stroke rate under no–load .......................................................
Lengths of stroke .....................................................................
Bevel cuts up to .......................................................................
Cutting depth max. in:
Soft- wood ............................................................................
Hard-wood ............................................................................
Steel .....................................................................................
Aluminium .............................................................................
Weight without cable ...............................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level ............................................................
Sound power level ................................................................
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Always use the protective shields on the machine.
Dust that arises when working on material containing
asbestos or stonework containing crystalline silicic acid is
harmful to the health. Please follow accident prevention
regulations.
Dust that arises when working on wood or using the tool on
industrial material can be dangerous to health. In this case
connect the tool to a suitable suction device.
Do not use cracked or distorted saw blades.
Plunge cuts without pre–drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must first be drilled with a hole
corresponding to the size of the saw blade.
SPECIFIED CONDITIONS OF USE
This jig saw can cut wood, plastic and metal; it can cut
straight lines, bevels, curves, and internal cut–outs.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50144, EN 55014–1, EN 55014–2,
EN 61000–3–2, EN 61000–3–3, in accordance with the
regulations 98/37/EC, 89/336/EEC
Manager Product Development
19 ENGLISH
Volker Siegle
STEP 70 STEP 75
.........500 W ..............540 W ............. 570 W ................600 W
.........250 W ..............270 W ............. 285 W ................300 W
1000-3200 /min ..1000-3200 /min . 1000-3200 /min ....1000-3200 /min
...........19 mm .............19 mm ............. 19 mm ...............19 mm
......... 45° ................. 45° .................. 45° ................... 45°
...........70 mm .............75 mm ............. 90 mm .............100 mm
...........60 mm .............65 mm ............. 70 mm ...............70 mm
.............5 mm ...............6 mm ............... 8 mm .................8 mm
...........10 mm .............10 mm ............. 15 mm ...............15 mm
..........1,9 kg ...............1,9 kg .............. 2,0 kg ................2,0 kg
..........4,5 m/s ............4,5 m/s
2
...........89 dB (A) .........89 dB (A) ........ 89 dB (A) ...........89 dB (A)
.........102 dB (A) .......102 dB (A) ...... 102 dB (A) .........102 dB (A)
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
STEP 90X STEP 100X
.............. 5 m/s ................5 m/s
2 2 2