BH FITNESS H650 Instrucciones De Montaje página 11

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
1.(1) Main body; (53) Right pedal
marked with letter (R); (53) Left pedal
marked with letter (L), (55) Main post,
(56)
Post
bottom
Handlebar;
(58)
Handlebar cover, (60) bottle holder,
(71) Front stabiliser bar; (73) Rear
stabiliser bar; (74) Rear trim, (77) Rail,
(91) Backrest support, (92) Saddle
back; (93) Backrest trim; (97) Adapter.
Hardware pack containing: (5) Plain
washer M8; (61) Slot head bolts
M5x15; (62) Slot head bolts M8x20;
(63) Open spring washer; (64) Slot
head bolts M8x15; (65) Curve washer;
(75) Slot head bolts M4x12; (94) Slot
head bolts M6x15; Allen screw M6;
Allen key M5; Double ended ring
spanner; Pedal spanner.
2 Take the front stabiliser
wheels (71) and position it as shown in
Fig (71), insert bolts (64), fit the plain
washers (5), and tighten securely.
Take the rear stabiliser bar (73) and
position it on the machine's rear stand
bracket support (1), as shown in (Fig.
3), inserts bolts (64), fit the plain
washers (5) and tighten securely.
3
FITTING THE PEDALS
The assembly instructions for the
pedals must be followed to the letter,
fitting these incorrectly could damage
the screw thread on either the pedal or
the crank.
Right and left refer to the position that
the user adopts when sitting on the
saddle to do the exercises.
The right-hand pedal (53), marked with
the letter (R), screws onto the right-
hand crank, also marked with an (R), in
a clockwise direction. Tighten securely,
cover,
(57)
Monitor;
(59)
bar with
(Fig. 4).
The left-hand pedal (53), marked with
the letter (L), screws onto the left-hand
crank, also marked with an (L), in an
anti-clockwise
securely, (fig 4).
Once the pedals have been fitted,
insert the end of the pedal clip into the
slot on the pedal adjusting it to your
footwear on the ledge of the pedal.
4. FITTING THE MAIN POST.-
Take the main post (55) and insert the
bottom post cover (56). Bring the main
post (55) up to boss on the main body
(1), connect the terminals (99) (60)
(40) and (100), Fig.5.
Slip the main post (56) over the boss
on the main body (1), Fig.5, making
sure not to snag any of the cables.
Refit the screws (64), and the washers
(65), Fig.5, and tighten securely.
Lower the bottom trim section (56) for
the main post (55) down over the boss
section of the main body (1).
5. FITTING THE HANDLEBAR.-
Bring the handlebar (57) up to the
handlebar stem (55).
Refit the screws (62) and washers (6)
(63), Fig.6, and tighten securely, then
fit the bracket cover (59) and screw
with screw (61).
6. BOTTLE HOLDER ASSEMBLY.-
Place the bottle holder (60) in the tube
(55), and screw with screws (61)
Fig.6.
7. FITTING THE MONITOR.-
Next, connect terminals, sticking out of
the
handlebar
terminals, sticking out of the monitor
(58), Fig.6.
11
direction.
Tighten
post
(55),
and

Publicidad

Tabla de contenido
loading

Tabla de contenido