STAMOS Operator Manual De Instrucciones página 12

Ocultar thumbs Ver también para Operator:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
SHADING DEGREE TABLE
Process
1,5
6
10
15
30
40
60
Shielded electrodes
8
MAG
8
TIG
8
9
Heavy metal MIG
9
Light alloy MIG
10
Arc-air gouging
10
Plasma beam cutting
9
Microplasma arc
4
5
6
7
welding
1,5
6
10
15
30
40
60
CAUTION: The term "heavy metals" applies to steel, steel alloys, copper, copper alloys, etc.
As per European Standard EN 379:2003+A1:2009
CLEANING
Clean the helmet by wiping with a soft cloth.
Clean the cartridge surfaces regularly. Do not use strong cleaning solutions
Clean the helmet with neutral soap and lukewarm water
Do not use any strong cleaning liquids
Do not use any solvents to clean the helmet and the filter
Keep the sensors and the solar cells clean with a clean lint-free cloth
Exchange the inner and extern lenses if they are damaged (cracked, scratched, soiled or pitted)
Clean the filter with a clean lint-free cloth or with a cotton cloth
Do not immerse the lenses or the filter in water or any other liquid
Do not use cleaning liquids containing abrasive particles, solvents or oils
TROUBLESHOOTING
Common problems and remedies
Irregular Darkening or Dimming
Headband has been set unevenly and there is an uneven distance from the eyes to the filter lens
(reset the headband to reduce the difference to the filter)
Auto-darkening filter does not darken or flicker
1. Front cover lens is soiled or damaged (change the cover lens)
2. Sensors are soiled (clean the sensors surface)
Slow response
Operating temperature is too low
Poor vision
1. Front / inside cover lens and / or the filter is soiled (change lens)
2. There is insufficient ambient light
3. Shade number is incorrectly set (reset the shade number)
Welding helmet slips
Headband is not properly adjusted (readjust the headband).
22
Current A
70
100
125
150
175
200
225
250
300
350
400
9
10
11
12
13
9
10
11
12
10
11
12
13
10
11
12
13
11
12
13
11
12
13
14
10
11
12
13
8
9
10
11
12
70
100
125
150
175
200
225
250
300
350
400
Rev. 07.11.2016
REGULAR CONTROL OF DEVICE
Check the machine regularly for signs of damage. If the machine is damaged, please stop using it immediate-
ly and contact your customer service to solve the problem.
What to do in case of a problem?
450
500
600
Please contact your customer service and prepare following information:
14
Invoice number and serial number (the latter is to be found on the technical plate on the machine).
13
14
If relevant, a picture of the damaged, broken or defective part.
It will be easier for your customer service clerk to determine the source of the problem if you give a
14
detailed and precise description of the matter. The more detailed your information, the better
customer service will be able to solve your problem rapidly and efficiently!
14
15
CAUTION: Never open the machine without the authorization of your customer service. This can lead
to a loss of warranty!
SAFE BATTERY REMOVAL INSTRUCTION
450
500
600
Welding masks 2982 Blaster | 2983 Eagle Eye | 2984 Firestarter 500 | 2985 Legend | 2986 Pokerface
| 2987 Carbonic | 2988 BlackONE | 2989 Metalator are fitted with lithium batteries CR 2450.
To remove the battery, remove the battery fitting elements. Empty batteries are to be forwarded to an
entity responsible for disposal of this sort of waste.
Rev. 07.11.2016
23

Publicidad

Tabla de contenido
loading

Tabla de contenido