Safety Regulations; Safety Inspection; Operating Manual - Nussbaum SPRINTER MOBIL 2500 Instrucciones De Servicio

Ocultar thumbs Ver también para SPRINTER MOBIL 2500:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

4

Safety regulations

When working with systems comply with legal ac-
cident prevention regulations according to BGG
945, inspection of lifts; BGR 500 and operation of
systems; VBG 14.
Particular attention is drawn to compliance with
the following regulations:
• When operating the system, follow safety regula-
tions and operating instructions in the operating
manual.
• The total weight of the accepted load may not
exceed
- 2,500 kg for SPRINTER MOBIL 2500 - HYMAX PRO
2500 and
- 3,000 kg for SPRINTER MOBIL 3000 - HYMAX PRO
3000, where a maximum load distribution of 3:2
or 2:3 in or against the drive-in direction is per-
mitted.
• Only personnel aged 18 or over may operate
systems independently, they must be trained in
system operation and have their work verified by
the company. They must be explicitly tasked with
operating the system (excerpt from BGR 500), see
transfer protocol.
• Operation of the system is only permitted on a
smooth, solid surface.
• During lifting or lowering, the work area of the sys-
tem should be clear or people.
• It is prohibited from moving people with the lift.
• It is prohibited to climb onto the system.
• After design and maintenance on load bearing
parts the system must be inspected by a techni-
cal expert.
• Initial access into the system may only be done
after the main switch (2) is off and locked.
• For vehicles with low floor clearance or custom
equipment, check in advance whether it could
be damaged.
• Consider any possible centre of mass shifts when
disassembling heavy vehicle components.
4.1

Safety inspection

The safety inspection is required to guarantee oper-
ational safety of the lift system. It is to be done:
1. Before first commissioning after setting up the lift
system use the „single safety inspection" form
2. After first commissioning, check regularly at least
once per year.
Use the „regular safety inspection" form
3. After changes to the lift system construction
Use the „extraordinary safety inspection" form
Single and regular safety inspections must be
!
done by a specialist. It is recommended to do
maintenance at the same time.
OPI_SPRINTER MOBIL 2500-3000_V3.1_DE-EN-FR-ES-IT
After a change in construction (for example
i
changing the load carrying capacity or chang-
ing the lifting height) and after significant main-
tenance on load carrying parts (e.g. welding
work), inspection by a technical expert is re-
quired (extraordinary safety inspection)
This inspection book contains forms with a detailed
inspection plan for safety inspections. Please use
the appropriate form, record the condition of the
inspected system and leave the completed form in
this inspection book.
5

Operating manual

When handling the system, it must
absolutely comply with safety regula-
tions. Carefully read the safety regu-
lations in Section 3 before first opera-
tion!
To prevent operation by unauthorized
people, secure the main switch (2) af-
ter working height has been reached.
2
1 Cover hood
2 Main switch
3 "LIFT" button
4 "LOWER" button
For SPRINTER MOBIL - HYMAX PRO lifts,
the motor of the vehicle supported
must always be on the fixed bearing
side, otherwise the vehicle could fall.
The total centre of mass of the vehi-
cle and its load must be between 100
mm and 600 mm away from the fixed
bearing towards the middle of the lift,
otherwise the vehicle could fall.
Slowly drive the vehicle to the middle in both the
lengthwise and crosswise directions over the drive-
3/4
1
59

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sprinter mobil 3000Hymax pro 3000Hymax pro 2500

Tabla de contenido