FALMEC Piano Manual De Instrucciones página 44

OpEraTION
WHEN SHOULD THE HOOD BE SWITCHED ON aND OFF?
Switch on the hood at least one minute before starting to cook: this enhances the airlow to
convey fumes and vapours towards the suction surface. fter cooking, leave the hood operat-
ing until complete extraction of all vapours and odours.
WHICH SpEED IS TO BE SELECTED?
The irst speed is a low consumption energy-saving way of keeping the air clean, the sec-
ond speed is used in normal conditions, and the third speed is used when there are strong
odours and vapours.
WHEN SHOULD THE FILTErS BE WaSHED Or rEpLaCED?
The hood has a metal anti-grease ilter (washable): this must be cleaned every 30 hours of
use.
For further information, please read the chapter regarding "Maintenance" on page 44.
OpENING OF aDJUSTaBLE FLapS
The adjustable laps on the suction unit move by rotation of the knurled knob: their rotation
is not continuous, but is in steps of 45° (see Phase
The laps must be directed towards the cooker top to ensure eicient suction (Fig.
suction unit is positioned between two cooker tops, both used, we recommend keeping the
3
laps in vertical position (Fig. ).
The hood is supplied with a safety device which prevents operation of
the motor should the adjustable laps of the suction unit be in the closed
position.
USE OF ELECTrONIC pUSH BUTTON CONTrOL paNEL
1 2
With LED on (speed 1 already running):
Pressing this key will switch of the hood motor and the LED associated with
the key.
1
With LED of
Pressing this key will start (in the event no speed is active) or sets the hood
at speed 1 (the function starts when the key is released); when speed 1 is
running, the relative LED lights up.
With LED on (speed 2 already running):
Pressing this key will switch of the hood motor and the LED associated with
the key.
With LED of
2
Pressing this key will start (in the event no speed is active) or sets the hood
at speed 2 (the function starts when the key is released); when speed 2 is
running, the relative LED lights up.
With LED on (speed 3 already running):
Pressing this key will switch of the hood motor and the LED associated with
the key.
With LED of
3
Pressing this key will start (in the event no speed is active) or sets the hood
at speed 3 (the function starts when the key is released); when speed 3 is
running, the relative LED lights up.
With LED on (speed 4 already running):
Pressing this key will switch of the hood motor and the LED associated with
the key.
With LED of
Pressing this key will start (in the event no speed is active) or sets the hood
4
at speed 4 (the function starts when the key is released); when speed 4 is
running, the relative LED lights up with intermittent light. The 4th speed or
intensive setting is timed and after about 7 minutes the motor automatically
switches to the 3rd speed.
The hood is supplied with a safety device which prevents operation of
the motor should the adjustable laps of the suction unit be in the
closed position.
If the hood is switched of by closing the laps, when they reopen the
motor starts at the previously selected speed prior to switching of.
S
1
on page 34 - Fig. )
2
): if the
3 4
MaINTENaNCE
Before cleaning or carrying out maintenance operations, disconnect the
equipment by removing the plug or switching of the main switch. Regular
maintenance guarantees proper operation and good performance over time.
Special attention is to be paid to the metal anti-grease ilters. In fact, frequent
cleaning of the ilters and their supports helps ensure that no grease accumulates on the
hood, which is dangerous and can cause ires.
EXTErNaL CLEaNING
You are advised to clean the external surfaces of the hood at least once every 15 days to
prevent oily substances and grease from sticking to them.
To facilitate cleaning of the adjustable laps, we recommend removing the part that sup-
ports them (EV) from the suction unit (Ua) (see the instructions
further details on this operation read phase
To clean the brushed stainless steel hood, the Manufacturer recommends using "Magic
Steel" wipes. Alternatively, it can be cleaned using a damp cloth, slightly moistened with
neutral, liquid detergent or denatured alcohol. Finish of cleaning by rinsing well and drying
with soft cloths.
Do not use too much water next to the push button control panel in order
to prevent humidity from reaching electronic parts.
You must not use detergents containing abrasive, acid or corrosive sub-
stances or abrasive cloths: a direct consequence of not complying with
these warnings will result in irreversible deterioration of the hood's surface.
The Manufacturer declines all responsibility for failure to comply with these instructions.
CLEaNING OF INTErNaL parTS
It is forbidden to clean electrical parts, or parts related to the motor inside the
hood, with liquids or solvents.
The inside of the suction unit can be cleaned, see the instructions
1 4
33 (Figures from to ).
Do not use abrasive products.
all these operations are to be carried out after having disconnected the equipment
from the electrical mains power supply.
METaL aNTI-GrEaSE FILTErS
The metal anti-grease ilters are there to contain suspended
grease particles: deposited on the ilters, these feed on any
lames released when cooking, generate unpleasant
odours, and compromise the passage of air, thus reducing
suction performance of the hood. For this reason, it is ad-
vised to frequently wash the metal ilters (at least once a
month) leaving them to soak in boiling water and washing
up liquid for 1 hour, taking care not to bend them. Do not
use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry
before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the ilter material to darken: to
reduce the possibility of this problem from happening, use low-temperature washes (55°C
max.).
To extract the metal anti-grease ilter, remove the part with the adjustable laps from the
suction unit (see the instructions
3
handle (Fig. ).
We recommend you clean the drilled part (B)(Fig.
4
at the same time ): use boiling water and a damp cloth slightly moistened with neutral
liquid or washing up liquid.
Do not use corrosive, acid or alkaline detergents.
Finish of cleaning by rinsing of well and wait for the parts to be completely dry before
reassembling them.
Reposition the drilled part and the metal anti-grease ilter by following, in reverse order, the
3
operations described in Fig. .
GrEaSE DrIp TraY
The grease drip tray collects the oil and grease that are de-
posited on the metal anti-grease ilters.
The metal ilters retain the grease and oil thanks to their
inclination and by being heated when ired and let them
low into the tray positioned beneath the suction unit near
the lower part of the ilters. It is advisable to empty the tray
at constant intervals depending on the use (approxi-
mately every 15 days) and wash it with boiling water and
washing up liquid.
Do not use corrosive, acid or alkaline detergents.
Rinse it well and wait for it to be completely dry before re-
assembling it.
Remove the grease drip tray by accessing the bottom of the suction unit (see the instruc-
Q
3
tions on page 33 - (Fig. ): be careful to keep the tray has horizontal as possible
6
when removing it (Fig. ).
44
Q
H
of the "assembly instructions".
Q
1 2
on page 33 - (Fig. - ) and lift the ilter by the
5
) and the inside of the suction unit (Fig.
on page 33): for
Q
on page