Technical Data - AEG PN 18 X Instrucciones De Uso

TECHNICAL DATA

Drilling capacity in concrete .....................................................
Drilling capacity in steel ...........................................................
Drilling capacity in wood ..........................................................
No-load speed .........................................................................
Single impact strength .............................................................
Battery .....................................................................................
Battery voltage ........................................................................
Weight with battery ..................................................................
Typical A-weighted sound levels:
Sound pressure level ...........................................................
Sound power level ...............................................................
Wear ear protectors!
Typical weighted acceleration in the hand-arm area ...............
Measured values determined according to EN 50 260.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Dust that arises when working on material containing
asbestos or stonework containing crystalline silicic acid is
harmful to the health. Please follow accident prevention
regulations.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. AEG Distributors offer to retrieve
old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System 3000 chargers for charging System 3000
battery packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section
of the charger (short circuit risk).
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The battery rotary pneumatic hammer can be used for
hammer drilling and drilling in wood, metal as well as plastic
for independent use away from mains supply.
Do not use this product in any other way as stated for
normal use.
19 ENGLISH
PN 18 X
...........................18 mm ..........................20 mm
...........................10 mm ..........................13 mm
...........................26 mm ..........................30 mm
.......................1050 min .........................1150 min
-1
..........................1,9 J ..............................2,3 J
.......................NiCd ............................NiCd
...........................18 V .........................24 V
..........................3,5 kg ..........................3,95 kg
...........................90 dB (A) ......................90 dB (A)
.........................101 dB (A) ....................101 dB (A)
..........................8,5 m/s ........................8,5 m/s
2
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50260, EN 55014-1, EN 55014-2, in
accordance with the regulations 98/37/EEC, 89/336/EEC
Manager Product Development
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
Temperatures in excess of 50
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition
to exchanging the brushes the tool should be sent to after-
sales service. This will ensure long service life and top
performance.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Accessory - Not included in standard
equipment, available as an accessory.
Remove the battery pack before starting
any work on the machine.
PN 24
-1
2
Volker Siegle
C (122 F) reduce the
o o