Accessories; Sawing With Special Base Runners; Sawing With The Angle Table; Sawing With The Adaptation Table - Festool CARVEX PSC 400 EB Manual De Instrucciones Original/Lista De Piezas De Repuesto

10

Accessories

Use only original Festool accessories and Festool
consumable material intended for this machine
because these components are designed specif-
ically for the machine. Using accessories and
consumable material from other suppliers will
most likely affect the quality of your working re-
sults and limit any warranty claims. Machine
wear or your own personal workload may in-
crease depending on the application. Protect
yourself and your machine, and preserve your
warranty claims by always using original Festool
accessories and Festool consumable material!
The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet under "www.festool.com".
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli-
cations that are specially designed for your Fes-
tool jigsaw.
10.2

Sawing with special base runners

The special base runners protect high-quality
surfaces against scratches and scores.
X
Press in the base runner at position [7-1].
X At the same time, push the base runner for-
wards.
X Mount another base runner and push it to
the rear until it engages.
10.3

Sawing with the angle table

The angle table WT-PS 400 is used for sawing
interior and exterior angles up to 45° and
pipes.
Dust extraction is not possible when
sawing with the angle table!
Installing the angle table
X
Remove the saw table [1-10], (see chap-
ter 7.4).
X
Position the angle table against the saw
table support.
X Close the change lever [1-8].
Ensure that the angle table is firmly seated in
the guide.
Setting the angle
X
Turn the adjusting wheel
desired angle.
You can set the values -45°, 0° and +45° us-
ing the scale [8-2].
L For 90° cuts, we recommend setting the
10.4
The adaptation table ADT-PS 400 is used for fit-
ting your jigsaw on the Festool guide rail and
the circle cutter KS-PS 400.
Installing the adaptation table
X
X
X
Ensure that the adaptation table is firmly seat-
ed in the guide.
L Use the extractor connector
Adaptation to the guide rail FS
The use of the Festool guide system FS (Picture
[10]) makes it easier to produce straight and
precise cuts, in particular, with material thick-
nesses up to 20 mm.
X
Adaptation to the circle cutter
The circle cutter can be used to create circular
cuts with a diameter between 120 and 3000
mm. The circle cutter can be installed from both
sides on the adaptation table.
X
[8-1] to set the
X
X
Angle table
position
Picture [8A] Angle, interior angle
Picture [8B] Angle
Picture [8C] Exterior angle, pipes
WARNING
Sawing cutting depths
Risk of injury
X Select the saw blade length and cutting
depth so that the saw blade always stays
in the workpiece.
angle table to a small negative degree
value to guarantee stable running.

Sawing with the adaptation table

Remove the saw table [1-10], (see chapter
7.4).
Mount the adaptation table
table support.
Close the change lever [1-8].
the adaptation table.
Mount the jigsaw with installed adaptation
table [9-1] on the guide rail.
Mount the jigsaw with adaptation table on
the adapter [11-1]
Insert the centring mandrel
bore [11-4] of the circle cutter, which is
aligned with the saw blade.
Clamp the measuring tape at the circle cut-
ter with the rotary knob [11-5].
CARVEX
Application
[9-1] on the saw
[1-7] also with
at the circle cutter.
[11-2] in the
GB
21