Ferroli CALLISTO Manual De Instalación, Uso Y Mantenimiento página 41

MENU 01 – Adjust fans
To set the hot air flow manually, the fan speed can be selected by choosing a value of 1 to 5; whereas for the fan
speed to be automatic and follow the selected power, choose the value A.
MENU 02 – Set clock
Before operating the stove , the current time and date must be set in order to have a reference for possible chrono
programming. The electronic control has a 3-volt lithium battery model CR2032 that gives the internal clock an
operation autonomy; battery replacement is necessary if the clock does not keep the time with the stove not
powered, or a series of zeros appears at restart: call an authorized service center.
To set the clock, access the menu by pressing STOVE and set the day with buttons P1 and P2. Press P7 again to
set the hours, minutes, day, month and year.
MENU 03 – Set chrono
Allows all time programming functions to be enabled/disabled. To enable the chrono, access the first submenu
ENABLE CHRONO and set it to ON with buttons P1 or P2. The manual commands from the emergency panel or
remote control have priority over programming.
The stove is equipped with three different types of programming: daily, weekly and weekend.
Chrono enabling is signaled by the LEDs shown in the picture below. Daily, weekly and weekend programming is
active only if the general chrono is enabled.
Access the second submenu DAY PROGRAM to enable or disable daily programming with buttons P1 and P2.
Then press button P7 and then buttons P1 and P2 to set up to two operation phases delimited by the set times.
Access the second submenu WEEK PROGRAM to enable, disable and set the weekly programming functions.
Follow the same procedures of the previous paragraph. Up to four operation phases delimited by the set times and
days can be set.
Carry out programming making sure not to overlap the hours of activation and/or deactivation on the same day in
different programs.
Access the third submenu WEEKEND PROGRAM to enable, disable and set the weekly programming functions for
the weekend. Follow the same procedures of the previous paragraph. Up to two operation phases delimited by the
times can be set.
To avoid unwanted startup and shutdown operations, activate only one program at a time.
MENU 04 – Select language
With this selection it is possible to set the desired language from those available.
MENU 05 – Standby mode
By selecting ON in STANDBY mode the corresponding symbol on the display lights up and the stove shuts down
automatically when the room temperature T has reached the set value (Tset + ΔT) for a given time.
The next restart in automatic will be possible only when the room temperature falls below the set value by a few
degrees and precisely (Tset - ΔT) where ΔT default = 2°C.
With the OFF selection, the modulation function is active but not the STANDBY mode. Therefore when the
temperature exceeds the set value the stove will operate at minimum power.
MENU 06 – Buzzer mode
With this selection it is possible to activate or deactivate the stove acoustic signals for alarms.
MENU 07 – Initial load
Allows the preloading of pellets for a given time. This function can only be activated when the stove is off and is
used if the auger is empty due to no more pellets. It is started with button P1 and stops with button P3.
MENU 08 – Stove/stove status
This selection is reserved for the COLA service center authorized technician.
MENU 09 – Technician settings
This selection is reserved for the COLA service center authorized technician.
Modification of the technical parameters of menu 09 must be done by authorized and competent personnel; any
random changes made can cause serious damage for which COLA declines any liability.
MENU 10 – Installer settings
This selection is reserved for the qualified installer and/or COLA service center authorized technician.
MENU 11 – ECO mode
Selecting ON in ECO mode limits stove operation to modulation, i.e. at minimum power. The display shows the
message ECO MOD.
41 CALLISTO