HIKOKI M 12V2 Instrucciones De Manejo página 9

D d
6 mm
12 mm
3/8"
3/8"
1/2"
10 mm
(3) Trimmer Guide (Fig. 20)
(4) Template Guide Adapter (B)
For the product of Trend.
Optional accessories are subject to change without notice.
APPLICATIONS
○ Wo o d wo r k i n g j o b s c e n te r e d o n g r o ov i n g a n d
chamfering.
PRIOR TO OPERATION
1. Power source
E n s u r e t h a t t h e p owe r s o u r c e t o b e u t i l i ze d
conforms to the power requirements specified on
the product nameplate.
2. Power switch
E n s u r e t h a t t h e p o we r s w i t c h i s i n t h e O F F
position. If the plug is connected to a receptacle
while the power switch is in the ON position, the
power tool will start operating immediately, which
could cause a serious accident.
3. Extension cord
When the work area is removed from the power
s o u r c e , u s e a n e x t e n s i o n c o r d o f s u f f i c i e n t
thickness and rated capacity. The extension cord
should be kept as short as practicable.
4 RCD
The use of a residual current device with a rated
residual current of 30 mA or less at all times is
recommended.
INSTALLING AND REMOVING BITS
WARNING
Be sure to switch power OFF and disconnect the
plug from the receptacle to avoid serious trouble.
1. Installing bits
(1) Clean and insert shank of bit into the collet chuck until
shank bottoms, then back it out approximately 2 mm.
(2) With the bit inserted and pressing the lock pin
holding the armature shaft, use the 23 mm wrench
to firmly tighten the collet chuck in a clockwise
direction (viewed from under the router). (Fig. 1)
CAUTION
○ Ensure that the collet chuck is firmly tightened
after inserting a bit. Failure to do so will result in
damage to the collet chuck.
○ Ensure that the lock pin is not inserted into the
armature shaft after tightening the collet chuck.
Failure to do so will result in damage to the collet
chuck, lock pin and armature shaft.
Shape of chuck sleeve
No groove
1 groove
2 grooves
No groove
(3) When using the 8 mm diameter shank bit, replace
the equipped collet chuck with the one for 8
mm diameter shank bit which is provided as the
standard accessory.
2. Removing Bits
When removing the bits, do so by following the
steps for installing bits in reverse order.
CAUTION
Ensure that the lock pin is not inserted into the
armature shaft after tightening the collet chuck.
Failure to do so will result in damage to the collet
chuck, lock pin and armature shaft.
HOW TO USE THE ROUTER
1. Adjusting depth of cut (Fig. 2)
(1) Place the tool on a fl at wood surface.
(2) Turn the quick adjustment lever in a counterclockwise
direction until the quick adjustment lever stops. (Fig. 3)
(3) Turn the stopper block so that section to which the
cutting depth setting screw on a stopper block is
not attached comes to the bottom of the stopper
pole. Loosen pole lock knob allowing the stopper
pole to contact with stopper block.
(4) Loosen the lock lever and press the tool body until
the bit just touches the flat surface. Tighten the
lock lever at this point. (Fig. 4)
(5) Tighten pole lock knob. Align the depth indicator
with the "0" graduation of scale.
(6) Loosen pole lock knob, and raise until indicator
aligns with the graduation representing the desired
cutting depth. Tighten pole lock knob.
(7) Loosen the lock lever and press the tool body
down until the stopper block to obtain the desired
cutting depth.
Your router allows you to fi nely adjust depth of cut.
(1) Attach knob to fi ne adjustment knob.
(2) Turn the quick adjustment lever in a clockwise
direction until the quick adjustment lever stops with
the stopper screw. (Fig. 5)
If the quick adjustment lever does not stop with
the stopper screw, the bolt screw is not properly
fi tted.
If this occurs, slightly loosen the lock lever and
press down on the unit (router) hard from the top
and turn the quick adjustment lever again after
properly fi tting the bolt screw.
(3) T h e d e p t h o f c u t c a n b e a d j u s te d w h e n t h e
l o c k l e v e r i s l o o s e n e d , b y t u r n i n g t h e f i n e
adjustment knob. Turning the fi ne adjustment knob
counterclockwise results in shallower cut, whereas
turning it clockwise results in a deeper cut.
CAUTION
Ensure that the lock lever is tightened after fi nely
adjusting depth of cut. Failure to do so will result
in damage to the quick adjustment lever.
2. Stopper block (Fig. 6)
The 2 cut-depth setting screws attached to the
stopper block can be adjusted to simultaneously
set 3 different cutting depth. Use a wrench to
tighten the nuts so that the cut- depth set ting
screws do not come loose at this time.
3. Guiding the router
WARNING
Be sure to switch power OFF and disconnect the
plug from the receptacle to avoid serious trouble.
English
9