Mackie ONYX-i Serie Guia De Inicio Rapido página 9

Front & Rear Panel Descriptions –
1. Power Connector & Switch
Connect the supplied AC power cord
to this IEC jack. The power switch turns the mixer on and off.
2. 48V Phantom Power Switches
3. XLR Inputs
Connect a balanced mic or line-level signal using
an XLR connector.
4. FireWire I/O
Allows you to stream audio to and from the mixer
via computer.
5. Line Inputs
Connect a balanced or unbalanced line-level signal
using a 1/4" connector.
6. Insert
Connect a serial effects processor, such as a compressor
or gate, using a 1/4" Y cable.
7. Aux
Adjusts the level sent from the channel Aux to the Aux send.
8. Gain
Adjusts the input sensitivity.
9. Low Cut Switch
Cuts bass frequencies below 75 Hz at a slope
of 18 dB per octave.
10. Equalization
Boost or cut the level at certain frequencies
to enhance the sound.
11. Pan
Adjusts how much of the signal is sent to the left
and right outputs.
12. Mute and OL LED
Mutes the channel signal. The OL LED
illuminates when a signal is too high or if the mute switch
is engaged.
13. Channel Fader
Adjusts the level to the main mix.
14. PFL/AFL Solo Switch
Allows you to listen to individual channels
singly or in combination with other soloed signals. The rude solo
LED flashes when solo switches are engaged.
15. Assign and Solo Switches
channel's signal to the bus(es) or Solo(s).
16. Main Out L/R
Connect to the inputs of amplifiers, powered
speakers, or a serial effects processor.
17. Main Mix
Adjusts the level of the signal sent to the main
outputs.
18. Phones
Connect stereo headphones here.
19. Recording Outputs
DB-25 balanced direct analog outputs
of channels 1-16.
20. CR/Phones
Controls the control room and headphones levels.
21. Alt 3-4 Out
1/4" outputs of all channels that have the Mute/Alt
3-4 switch engaged.
Provides 48V to individual inputs.
Determines the destination of the
EN ES FR DE
22. Sub Assign Switches
Assign each subgroup to the main left
and/or right buses.
23. Sub 1-4 Faders
Control the levels of the signals sent
to the sub outs and or main mix.
24. Tape Inputs / Outputs
RCA inputs allow you to connect a line-
level source. RCA outputs allow you to record the main stereo mix.
25. Tape Level
Controls the input level of a source connected
to the tape inputs.
26. Aux Master Control
Controls the level being sent from the
Aux sends.
27. Aux Send
1/4" outputs fed from the Aux Master controls.
28. Return Master Controls
Master level controls for the Stereo
Returns signal paths.
29. St/Return Inputs
Connect the stereo processed outputs
of an effects processor to these 1/4" TRS jacks.
30. Main Meters
Used to gauge the soloed input or output levels
to ensure that the signals are not clipping.
31. Stereo Line Inputs
Connect stereo balanced or unbalanced
line-level signals using 1/4" connectors.
32. Sub Outs
1/4" outputs fed from the Subgroups.
33. Left/Right and Mono Outs
or to monitor soloed channels.
34. Main Insert
Connect a serial effects processor(s) to the Main
such as a compressor or gate, using a 1/4" Y cable.
35. Talkback Mic Input
Connect an external talkback mic.
36. FireWire Send Pre/Post EQ Switches
is pre or post FireWire from each channel.
37. Pre Fader Switch
Determines if Aux sends are Pre or Post fader.
38. Control Room Assign Switches
Control Room output.
39. CR Out L/R
Feed the inputs of a control room amplifier,
studio monitors or a headphone distribution amplifier.
40. Input Switch
When engaged routes playback via the FireWire
connection into the channel (instead of the line input).
41. Talkback Master Controls
Used to control the Talkback mic
routing and level.
Use for additional main mix outputs
Determines if equalization
Determines the source of the
Quick Start Guide
9