Additional Information; Troubleshooting - Pioneer CDJ-900 Manual De Instrucciones

Multirreproductor
Ocultar thumbs Ver también para CDJ-900:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes
the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the
items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The CDJ-900 may not operate properly due to such external causes as static electricity. If this happens, normal operation can sometimes be restored by turning the
power off, waiting for the disc to stop completely, then turning the power back on.
! Non-finalized (partial discs) CD-R/ -RW cannot be played on the CDJ-900.
! Irregularly shaped discs other than standard 12 cm discs cannot be played on the CDJ-900 (doing so will lead to damage or accidents).
! The BPM measured by the CDJ-900 may differ from the BPM indicated on the disc or that of a Pioneer DJ mixer, etc. This is due to the different methods used for
measuring the BPM, and is not a malfunction.
Problem
Disc cannot be ejected.
Playback does not start when disc is loaded.
File cannot be played.
No sound is produced, or sound is distorted or noisy.
Loud noise is produced or playback stops when a
certain disc is played.
File information is not properly displayed.
Track search operation takes too long.
Back cue function does not work.
Loop play function does not work.
Settings are not stored in the memory.
USB device is not recognized.
Cue or loop points of tracks recorded on USB devices
are not stored in the memory.
Cue or loop points of tracks recorded on USB devices
are not displayed.
The playing address display is not displayed in the
remaining time mode.
Time is required to read USB devices (flash memory
drives and hard discs).
Library browsing is not possible.
[HISTORY] is not displayed.
Nothing is displayed.
PRO DJ LINK does not work well.
26
En
Check
Is the disc or file playable?
Is the auto cue function activated?
Is the file copyright-protected (by DRM)?
Are you operating the connected DJ mixer properly?
Is the CDJ-900 placed near a TV?
Is the disc scratched?
Is the disc dirty?
Is the information recorded in a language not supported
by the CDJ-900?
Is the auto cue function activated?
Is a cue point set?
Is a cue point set?
Has the power been turned off directly after changing the
setting?
Is the USB device properly connected?
Is the USB device connected via a USB hub?
Is the USB device supported by the CDJ-900?
Is the file format supported by the CDJ-900?
Is there sufficient free space on the USB device?
Has the USB device been properly removed?
Is there a large number of folders or files recorded on the
USB device?
Are files other than music files stored on the USB device?
Is a medium on which library information is recorded
loaded?
Is a USB device loaded?
Is the power management function activated?
Are the player numbers properly set?
Is the LAN cable properly connected?
Is the switching hub's power turned on?
Is an unnecessary device connected to the switching hub?
Remedy
If the [DISC EJECTh] button does not work, insert the pin in the disc force
eject pin insertion hole to eject the disc.
See Discs/ files playable on the CDJ-900 on page 6.
Press [AUTO CUE] for at least 1 second to turn cancel the auto cue function.
Copyright-protected files cannot be played.
Check the operation of the DJ mixer.
Turn the TV's power off, or install the CDJ-900 and TV away from one
another.
Scratched discs may not play.
Wipe the dirt off the disc (page 28).
When creating files using DJ software, etc., record the information in a
language supported by the CDJ-900.
Track searching may take some time when there are long silent sections
between tracks.
If track searching is not possible within 10 seconds, a cue point is set at the
beginning of the track.
Set the cue point (page 15).
Set the cue point (page 15).
After changing settings, wait at least 10 seconds before turning the power
off.
Connect the device securely (all the way in).
USB hubs cannot be used.
This player only supports USB mass storage class devices.
This player supports portable flash memory and digital audio playback
devices.
Check the file format of the connected USB device. For the file formats sup-
ported by the CDJ-900, see About USB devices on page 7.
Turn the power off then back on.
A maximum of 100 cue and loop points per disc can be recorded on USB
devices (10 per track for media other than discs). If you attempt to record
more points than the limit, [POINT FULL] is displayed and the points cannot
be recorded.
If there is not enough free space on the USB device or if the device is write-
protected, [USB FULL] is displayed and the points cannot be recorded.
Points may not be displayed if the USB device is removed without perform-
ing the proper stopping procedure or if the CDJ-900's power is turned off.
When playing files recorded in VBR, it may happen that the set cannot
detect the length of the track immediately and that some time is required for
the playing address display to appear.
When there are many folders or files, some time may be required for load-
ing.
When files other than music files are stored in folders, time is required to
read them as well. Do not store files or folders other than music files on the
USB device.
The library browse mode is only set when media on which library informa-
tion is recorded are loaded. When a medium on which no library information
is recorded is loaded, the folder browse mode is set.
The [HISTORY] function can only be used for DJ players on which a USB
device is loaded.
The CDJ-900 is shipped with the power management function turned on.
If you do not want to use the power management function, set [AUTO
STANDBY] to [OFF]. (page 20)
Set [PLAYER No.] to [AUTO] or to a number different from the number cur-
rently set. (page 20)
Connect the LAN cable properly to the [LINK] terminal.
Turn the switching hub's power on.
Disconnect the unnecessary device from the switching hub.

Publicidad

Tabla de contenido
loading

Tabla de contenido