Prior To Operation - Hitachi Koki DH 22PG Instrucciones De Manejo

English
Drilling holes in concrete or tile
Drill bit (slender shaft)
Outer dia. Overall length
3.4 mm
90 mm
3.5 mm
SDS-plus Drill bit
Outer dia. Overall length
4.0 mm 110 mm
110 mm
5.0 mm
160 mm
5.5 mm 110 mm
6.5 mm 160 mm
7.0 mm 160 mm
8.0 mm 160 mm
8.5 mm 160 mm
9.0 mm 160 mm
166 mm
12.0 mm
260 mm
12.7 mm 166 mm
14.0 mm 166 mm
15.0 mm 166 mm
166 mm
16.0 mm
260 mm
17.0 mm 166 mm
19.0 mm 260 mm
20.0 mm 250 mm
22.0 mm 250 mm
Drilling anchor holes
Taper shank adapter
Taper mode
Morse taper No.1
Morse taper No.2
A-Taper
Anchor setting
Anchor setting adapter
Anchor size
W 5/16"
Optional accessories are subject to change without notice.
7
Effective length
45 mm
Effective length
50 mm
50 mm
100 mm
50 mm
100 mm
100 mm
100 mm
100 mm
100 mm
100 mm
200 mm
100 mm
100 mm
100 mm
100 mm
200 mm
100 mm
200 mm
200 mm
200 mm
B-taper
W 1/4"
W 3/8"
APPLICATIONS
Rotation and hammering function
Drilling anchor holes
Drilling holes in concrete
Drilling holes in tile
Rotation only function
Drilling in steel or wood
(with optional accessories)
Tightening machine screws, wood screws
(with optional accessories)

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a power receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause a
serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Mounting the drill bit (Fig. 1)
CAUTION
To prevent accidents, make sure to turn the switch
off and disconnect the plug from the receptacle.
NOTE
When using tools such as bull points, drill bits, etc.,
make sure to use the genuine parts designated by
our company.
(1) Clean the shank portion of the drill bit.
(2) Insert the drill bit in a twisting manner into the tool
holder until it latches itself (Fig. 1).
(3) Check the latching by pulling on the drill bit.
(4) To remove the drill bit, fully pull the grip in the
direction of the arrow and pull out the drill bit (Fig. 2).
5. Installation of dust cup or dust collector (B)
(Optional accessories) (Fig. 3, Fig. 4)
When using a rotary hammer for upward drilling
operations attach a dust cup or dust collector (B) to
collect dust or particles for easy operation.
Installing the dust cup
Use the dust cup by attaching to the drill bit as shown
in Fig. 3.
When using a bit which has big diameter, enlarge the
center hole of the dust cup with this rotary hammer.
Installing dust collector (B)
When using dust collector (B), insert dust collector
(B) from the tip of the bit by aligning it to the groove
on the grip (Fig. 4).
CAUTION
The dust cup and dust collector (B) are for exclusive
use of concrete drilling work. Do not use them for
wood or metal drilling work.
Insert dust collector (B) completely into the chuck
part of the main unit.