Layout And Items Supplied; Proper Use - EINHELL TC-RH 800 E Manual De Instrucciones

•
Always check that the chisel bit or drill bit is
firmly locked in the chuck before you start
work.
•
Check the chuck for wear or damage at regu-
lar intervals.
•
Do not start a hammering tool until it is
pressed against a workpiece (wall, ceiling,
etc.).
•
Always unplug the hammer drill when you
have finished working and remove the chisel
bit or drill bit from the tool.
•
Always unplug the machine before changing
chisel bits or drill bits etc.
•
Protect eyes and assistants from small flying
parts and splinters. Wear a helmet! Erect a
screen wall!
•
Use workgloves to protect fingers from crus-
hing and skin from grazing.
•
Vibrations can be harmful to the hand-arm
system: Keep the impact time of vibrations to
a minimum.
•
Always keep the power cable away from whe-
re you want to drill.
•
Keep the machine out of children's reach.
•
Always hold the machine with two hands
when it is running and make sure of your
footing.
•
Make sure that the switch on the machine is
set to the correct position for the work you
want to perform before you put the machine
into opera-tion. If the switch is not in the cor-
rect position you risk suffering bodily injury
when the machine starts to run.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Do not lose these safety instructions

2. Layout and items supplied

2.1 Layout (Fig. 1)
1. Dust guard
2. Locking sleeve
3. Selector switch for drill/hammer drill/chisel
4. ON/OFF switch
5. Locking button
6. Additional handle
Anl_SA_TC_RH_800_E_SPK8.indb 27 Anl_SA_TC_RH_800_E_SPK8.indb 27
GB
7. Depth stop
8. Handle
9. Speed controller
10. Clockwise/Counter-clockwise switch
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made bought the product
within the maximum days indicated by the con-
sumer protection laws of your country and upon
presentation of a valid bill of purchase. Also, refer
to the warranty table in the service information at
the end of the operating instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Hammer drill
•
Additional handle
•
Depth stop
•
Original operating instructions
•
Safety instructions

3. Proper use

The tool is designed for drilling with hammer ac-
tion in concrete, rock and brick, as well as for chi-
seling work, always using the respective correct
drill or chisel bit.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
- 27 -
24.10.2017 10:20:27 24.10.2017 10:20:27