Best Strip Vetro HF Nero 90 Instrucciones De Uso página 16

English
! The appliance must be installed by a qualified person
in compliance with the instructions provided.
!
Wear gloves when carrying out installation and
maintenance operations.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Warning: Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.
The hood can look different to that illustrated in the
drawings in this booklet. The instructions for use,
maintenance and installation, however, remain the
same.
- Only for hoods equipped with electronic control of
Fig.24-25-26:
The 4th speed (intensive) is automatically lowered to 3rd
speed after 5 minutes of operation to optimise energy
consumption.
- Only for hoods equipped with electronic control of
Fig.27: In order to optimize energy consumption, high
speed of work signaled by red LEDs (L) will be
automatically reduced to standard speed after 5 minutes
of work.
- If the hood is left on (lights and/or motor), after 10
hours in the absence of commands from the user, it will
automatically switch to OFF condition with all services
switched off.
- The Buzzer emits a "beep" each time that a command
is set from the keyboard or remote control (optional).
- In the event of interruption of power during the hood, if
you restore the hood in the OFF state, then the engine
must be reactivate manually.
AIR VENT
(for ducting versions)
! Prepare the hole and the air vent duct (150 mm
diameter).
! Use a duct of the minimum indispensible length.
! Use a duct with as few elbows as possible (maximum
elbow angle: 90°).
! Avoid drastic changes in the duct cross-section.
! Use a duct with an as smooth as possible inside.
! The duct must be made of certified material.
! Do not connect the hood to smoke exhaust ducts for
the products of combustion (boilers, fireplaces,
stoves, etc).
! For the air vents comply with the provisions laid down
by the competent authorities.
In addition, the air must not be evacuated through a
hole in the wall unless specifically intended for this
purpose.
! Fit air intakes in the room to prevent the hood from
creating a negative pressure in the room (which must
not exceed 0.04 mbar); if the hood is used at the same
time as non-electrical equipment (gas-, oil- and
charcoal-fired stoves, etc.) the exhaust gas may be
sucked in by the heat source.
FILTERING OR DUCTING VERSION ?
The hood may be in filtering or in ducting version.
Decide from the outset which type is to be installed.
For better efficiency, we recommend installing the hood
in the ducting version (if possible).
Ducting version
Version with external motor
The hood purifies the air and evacuates it to the outside
through an exhaust duct (diameter 150 mm).
Filtering version
The hood purifies the air and recycles the clean air back
into the room.
CONTROLS
CONTROLS Fig.24:
P1: Filter alarm reset
P2: LED on/off - (only certain models: holding the button
down you can change the LED intensity to High or
Low).
Note: LED activation is displayed by P2 only when
the lift panel is completely open.
P3: Motor on/off - 1st speed
P4: 2nd speed
P5: 3rd speed
P6: 4th speed
P7: Lift panel up/down (during opening the panel can be
stopped at the desired height by pressing the
button a second time).
5' Timer function:
Holding the buttons P3, P4, P5 or P6 pressed down
(>2") the 5' Timer function is activated. When the time
has run out, the motor turns off. When the function is
active, the LED corresponding to the current motor
speed blinks.
Filter alarm display:
Grease filters: After 30h of motor operation, the LED of
the P1 button comes on for 30'' every time the motor
turns off.
Charcoal filter: After 120h of motor operation, the LED of
the P1 button blinks for 30'' every time the motor turns
off.
CONTROLS Fig.25:
P1: Filter alarm reset
P2: Motor on/off - 1st speed
P3: 2nd speed
P4: 3rd speed
P5: 4th speed
P6: Lift panel up/down (during opening the panel can be
stopped at the desired height by pressing the
button a second time).