Care And Maintenance; Waste Disposal - Proxxon BSG 220 Manual De Instrucciones

Relief angle adjustment:
The relief angle is generally adjusted by the
positioning in the clamp (Fig. 5). The relief
angle setting is factory set for the drill
diameters from 3 to 13 mm and should only
be adjusted in exceptional cases.
Adjust hexagon nut 1 (Fig. 13) of the adjustment
spindle according to table (Fig. 12).
Dressing the grinding wheel:
If grooves have formed or if the grinding
wheel is blocked it must be dressed, in order
to achieve good grinding results.
Attention!
Wear goggles!
1. Switch the drill grinder on by the ON – OFF
switch 7 (Fig. 1).
2. Press knob 1 (Fig. 14) slightly down and
move the pressing part 2 several times up
and down, until the complete front face of the
grinding wheel has been processed.
Replacing the grinding wheel:
Attention!
Replace the grinding wheel once it has
reached a diameter of less than 45 mm. A
spare grinding wheel Part-No.: 21200-58 is
delivered with the machine.
1. Pull out the mains plug.
2. Remove cap 1 (Fig. 15) with a screwdriver or
similar.
3. Unscrew socket head cap screw 2 (Fig. 15),
remove washer 3 and grinding wheel 5 with
clamping flange 4.
4. Mount the new grinding wheel 5 with
clamping flange 4 and washer 3. Tighten
socket head cap screw 2 and plug on cap 1.
Plug in the main plug.
Note!
Note!

Care and maintenance:

The drill grinder is almost maintenance free. For
a long lifetime you should clean the machine after
each use with compressed air and a soft cloth,
because the grinding dust is very aggressive.

Waste disposal:

Do not dispose of the machine with your
normal household refuse! The machine
contains materials which can be recycled. If you
have any questions on this matter please ask
your local waste disposal company or other
municipal facilities.
EC Declaration of Conformity:
EC Declaration of Conformity
Name and address:
Name and address of manufacturer:
PROXXON S.A.
6-10, Härebierg
PROXXON S.A.
L-6868 Wecker
6-10, Härebierg
L-6868 Wecker
Product designation:
Article No.:
Product name:
In sole responsibility, we declare that this product
Drill grinder BSG 220
conforms to the following directives and norma-
Article number: 21200
tive documents:
We declare in sole responsibility that this product
EU EMC Directive 2004/108/EC
complies with the following standards and
DIN EN 55014-1 / 05.2012
normative documents:
DIN EN 55014-2 / 06.2009
DIN EN 61000-3-2 / 03.2010
EC machine regulation 98/037/EEC
Applied standards: DIN EN 61000-3-3 / 07.2012
DIN EN 61029-1/12.2003
EU Machinery Directive 2006/42/EC
Low voltage regulations 89/336/EEC
DIN EN 61029-1 / 01.2010
Applied standards:
DIN EN 61029-1/12.2003
Date: 16.10.2012
EC-EMC directive 89/336/EEC
Applied standards:
EN 55014-1: 1999
EN 55014-2: 1997
EN 61000-3-2: 1995
EN 61000-3-3:1995
Dipl.-Ing. Jörg Wagner
Date: 15.03.2005
Dipl.-Ing. Jörg Wagner
PROXXON S.A.
Machine Safety Department
PROXXON S.A.
Sphere of activity Machine safety
The CE document authorized agent is identical
with the signatory.
BSG 220
21200
- 13 -