Peg-Perego VIAGGIO 0+1 SWITCHABLE Instrucciones De Uso página 27

car • Do not use this car seat if more than seven years have
d elapsed from the date of production indicated on the
structure; the natural aging of the materials may mean the
car seat is no longer compliant with safety standards.
• Do not use accessories that have not been approved by
the manufacturer or by the competent authorities.
Instructions for use
e
UNIVERSAL CATEGORY - Belted
Group 0+
Fastening with seatbelts
ble
IMPORTANT: For the correct use of the
1•
t.
"Viaggio 0+1 Switchable" car seat in Group 0+
mode, it is necessary to:
- Extract from under the seat the casing that enables
d
the car seat to be reclined.
l
To extract it, press the handle and pull it towards
t
you, extracting the base (arrows A and B).
- Use the lever (arrow C) to recline the seat to its
highest position.
2• "Viaggio 0+1 Switchable" car seat correctly installed to
t
be used as a Group 0+ car seat.
3• Install the "Viaggio 0+1 Switchable" car seat on the
e
vehicle's seat so that it is rear-facing, as shown in the figure.
Pass the vehicle seatbelt between the frame and body
e
of the car seat following these steps:
al
- slip the belt into the light blue belt guides first (arrow A);
- fasten the belt, ensuring that it clicks into place (arrow B);
ng
4• Pass the seatbelt through the upper light blue belt slot
(arrow C).
IMPORTANT: Take hold of the seatbelt and pull
it firmly, so as to ensure that the "Viaggio 0+1
Switchable" fits as close as possible to the vehicle
seat (arrow D).
Instructions for use
UNIVERSAL CATEGORY - Belted
Group 1
f
Fastening with seatbelts
5• IMPORTANT: For the correct use of the "Viaggio 0+1
Switchable" car seat in Group 1 mode, it is necessary to:
- Reposition the casing within the base of the car seat.
Press the lever and push inwards, as indicated in
the figure.
6• Install the "Viaggio 0+1 Switchable" car seat on the vehicle's
seat so that it is front-facing, as shown in the figure.
7• To make it easier to pass the vehicle's seatbelts
through the back of the car seat, it is necessary to
recline the car seat to its lowest position by operating
the lever, as shown in the figure.
8• Pass the vehicle seatbelt between the frame and body
of the car seat.
9• The waist strap must pass through the lower guides,
marked in red; fasten the belt, ensuring that it clicks
into place.
10• Tighten the waist strap, ensuring it has passed through
the lower guides, marked in red.
11• Bring the car seat back into the upright position by
pulling the handle below the seat (Fig. A) and pushing
the car seat as shown in the figure (Fig. B).
12• To complete the installation process, use the Steady
Fix device: open the clip and pass the diagonal strap
through it, ensuring that it is taut and not twisted (Fig.
A). Close the safety tab (Fig. B).
13• IMPORTANT: Take hold of the seatbelt and pull
it firmly upwards, so as to ensure that the "Viaggio
0+1 Switchable" fits as close as possible to the
vehicle seat (Fig. C).
Once installed, the car seat may be reclined to the
desired position (See Point 6).
How to secure your child in the
"Viaggio 0+1 Switchable" car seat
14• Before placing the child in the car seat, release the
harness by pushing the red button on the crotch strap
buckle.
15• Lift the harness and attach the buckles to the elastic
bands on the sides.
16• Place the child in the car seat and arrange the harness over
the child's shoulders and waist, as shown in the figure.
27