Peg-Perego VIAGGIO 0+1 SWITCHABLE Instrucciones De Uso página 28

17• Lock the harness by overlapping the tongues and
inserting them into the buckle of the crotch strap until
they click into place.
18• The child is now sitting correctly with the harness
fastened properly.
19• Finally, tighten the shoulder straps until they are snug
to the child's body by pulling the central adjustment
strap towards you, as shown in the figure, taking care
not to over-tighten the straps.
IMPORTANT: Leave minimal slack (the space of
a finger) between the strap and the child's chest.
20• To slacken the straps, press the button at the centre
of the car seat and at the same time pull the straps
towards you.
IMPORTANT: Take hold of the straps under the
shoulder pads and pull, as shown in the figure.
21• The car seat has a booster cushion which is only
suitable for small babies. When the child is older,
remove the booster cushion.
• To remove the booster cushion, unfasten the seatbelts,
slide them off the booster cushion and slide the crotch
strap out through the slot in the booster cushion.
IMPORTANT: The booster cushion must be
removed when the "Viaggio 0+1 Switchable" is
used as a Group 1 car seat.
How to adjust the height of the headrest
The headrest must be adjusted to match the child's
height. There are 7 positions.
22• To change from a lower position to a higher one: pull
the tongue in the upper central part of the headrest
upwards. The headrest will move at the same time.
To change from a higher position to a lower one: pull
the tongue in the upper central part of the headrest
upwards and, at the same time, push the headrest
down to the desired position.
When you have finished, try moving the headrest
to check it is properly locked into place.
23• WARNING: Do not use the car seat in Group 0+ mode
without first extracting the casing, as shown in point 1
A-B (Fig.A).
WARNING: Do not use the car seat in Group 0+ mode
without first reclining the backrest, as shown in point
1C (Fig.B).
24• Use in Group 0+ mode: To determine the best
shoulder strap position, bear in mind that the child's
shoulders must be just above the shoulder strap guides.
25• IMPORTANT: The straps must not be too high or
too low with respect to the child's shoulders.
26• WARNING: Do not use the car seat in Group 1 mode
with the casing extracted.
27• Use in Group 1 mode: To determine the best shoulder
strap position, bear in mind that the child's shoulders
must be just below the shoulder strap guides.
28• IMPORTANT: The straps must not be too high or
too low with respect to the child's shoulders.
IMPORTANT: The "Viaggio 0+1 Switchable" car seat
29•
can be reclined into 5 different positions only when it
is used in Group 1 mode.
To recline the car seat, press the lever under the
seat (Fig.A) and pull to adjust the seat to the desired
position (Fig.B).
How to remove the soft cover
To remove the soft cover of the "Viaggio 0+1
Switchable" car seat:
• Remove the booster cushion, where present (point 20).
• Unfasten the harness (point 13).
• Open the rear panel.
30• Unfasten the straps from the rear latch plate.
31• Unfasten the straps on the rear and slip them out from
the front.
32• Unfasten the shoulder pads from the rear and slip
them off the straps from the front.
33• Slip off the adjuster strap (Fig. C) and then remove the
headrest cover from above (Fig. D).
34• Release the crotch strap from below the body (Fig. E) and
slide the strap out through the crotch strap cover (Fig. F).
35• Slip the strap out through the opening in the soft cover
and remove the soft cover, as shown in the figure.
Soft cover maintenance
Brush the fabric parts to remove dust.
• Before placing the soft cover in the washing machine,
slide the foam rubber cushion out of the booster seat
from the rear.
28
36
37
38
39
40
41
42
43
44
45
46