General Safety; Product Familiarisation; Intended Use - Silverline 261362 Manual De Instrucciones

261362

General Safety

WARNING: Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you
to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the OFF-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energising power tools that have the switch ON invites accidents.
d) Remove any adjusting key or wrench before turning the power tool ON. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent
and ignore tool safety principles. A careless action can cause severe injury within a fraction of a
second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it ON and OFF. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack, if detachable,
from the power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
DIY 110W Orbital Car Polisher 240mm
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Polisher Safety
• Do not use this polisher as an angle grinder
• Always read and understand all information supplied with polishing pastes before use
• Do not smoke, eat, or drink when using this polisher
• Never attach any accessory with a maximum speed lower than the no load speed of the machine

Product Familiarisation

1. ON/OFF Switch
2. Handles
3. Polishing Pad

Intended Use

Electrical orbital polishing tool for light to medium duty polishing tasks on vehicles of all kinds and
other similar surfaces .
Unpacking Your Tool
• Carefully unpack and inspect your new sander . Familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition . If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the polisher is disconnected from the power supply before attaching or
changing any accessories .
Fitting a polishing bonnet
• Polishing bonnets can be fitted over the Polishing Pad (3)
• If using tie string type bonnets, ensure that tie strings are secure, and will not snag on any part of
the machine
Operation
WARNING: ALWAYS wear appropriate personal protective equipment, including eye protection
when working with this tool .
Switching ON
1. Put on all safety equipment required to use this tool and connect the tool to the power source
2 . Grip the polisher by both hands, using both of the Handles (2)
3. Slide the ON/OFF Switch (1) into the 'ON' position
4 . To switch OFF the polisher, slide the switch to the 'OFF' position
Polishing tips
• ALWAYS ensure that the area to be polished is clean and dry
• Read and understand all information supplied with your polishing compound or paste before
use
• Apply polishing compound or paste to the polishing bonnet (follow manufacturers guidance),
and place polishing bonnet against work surface
• Hold the machine securely, using both hands, by the handles provided . The polishing bonnet
should lightly contact the work surface
• Start the machine, and work across the surface using a wide 'sweeping' motion. Apply extra
compound or paste as required
• When entire work surface is coated, stop the machine and allow compound or paste to dry
(follow manufacturers guidance)
• Attach a clean polishing bonnet to the machine, and work across the surface as before until all
polishing compound or paste is removed
silverlinetools.com
5