Programming Instructions - tau D760M Guía Para La Instalación

Motor 2 torque adjustment (swing 2). The trimmer is set to provide sufficient thrust
to work the gate without exceeding the limits established by current standards (EN
FR. M2
12453). Turning the trimmer clockwise (+) increases the motor torque, turning it anti-
clockwise (-) reduces it.
CH.AUTO Automatic closing time adjustment from 2 to 120 seconds.
turn the TRIMMER clockwise to increase adjustments; turn it anticlockwise to
Notice:
decrease.

PROGRAMMING INSTRUCTIONS

If a transmitter has been previously programmed, it can be used to perform the following procedure.
Otherwise, connect a Key Switch or a NO Pushbutton to the AP/CH wire terminals on the controller.
DOUBLE SWING GATE - DIP SWITCH # 4 in ON (Soft-Stop function enabled):
1 press and hold down for at least 5 seconds P1 and P2 buttons to activate the programming
mode;
2 the DL7 LED will begin blinking fast to confirm that programming mode is active;
3 press AP/CH button or the remote control: both leaves will open;
4 once opening is complete, press AP/CH button or the remote control: both leaves will stop;
5 press AP/CH button or the remote control: the leaf #2 will close at standard speed;
6 press AP/CH button or the remote control when the leaf should start to decelerate;
7 when the leaf is completely closed press AP/CH button or the remote control (leaf #2 program-
ming completed);
8 press AP/CH button or the remote control: the leaf #1 will close at standard speed;
9 press AP/CH button or the remote control when the leaf should start to decelerate;
10 when the leaf is completely closed press AP/CH button or the remote control (leaf #1 program-
ming completed);
11 the DL7 LED will stop blinking and remain steady ON (programming completed and saved).
SINGLE SWING GATE - DIP SWITCH # 4 in ON ( Soft-Stop function enabled):
1 press and hold down for at least 5 seconds P1 and P2 buttons to activate the programming
mode;
2 the DL7 LED will begin blinking fast to confirm that programming mode is active;
3 press AP/CH button or the remote control: the leaf will open;
4 once opening is complete, press AP/CH button or the remote control: the leaf will stop;
5 press 4 times AP/CH button or the remote control: the leaf will close at standard speed;
6 press AP/CH button or the remote control when the leaf should start to decelerate;
7 when the leaf is completely closed press AP/CH button or the remote control (leaf programming
completed);
8 the DL7 LED will stop blinking and remain steady ON (programming completed and saved).
GATE 2 WINGS - DIP SWITCH # 4 in OFF (Soft-Stop function disabled):
1 press and hold down for at least 5 seconds P1 and P2 buttons to activate the programming
mode;
2 the DL7 LED will begin blinking fast to confirm that programming mode is active;
3 press AP/CH button or the remote control: both leaves will open;
4 once opening is complete, press AP/CH button or the remote control: both leaves will stop;
5 press AP/CH button or the remote control: the leaf #2 will close at standard speed;
6 when the leaf is completely closed press AP/CH button or the remote control (leaf #2 program-
ming completed);
7 press AP/CH button or the remote control: the leaf #1 will close at standard speed;
8 when the leaf is completely closed press AP/CH button or the remote control (leaf #1 program-
ming completed);
9 the DL7 LED will stop blinking and remain steady ON (programming completed and saved).
GATE 1 WINGS - DIP SWITCH # 4 in OFF (Soft-Stop function disabled):
1 press and hold down for at least 5 seconds P1 and P2 buttons to activate the programming
mode;
2 the DL7 LED will begin blinking fast to confirm that programming mode is active;
3 press AP/CH button or the remote control: the leaf will open;
4 once opening is complete, press AP/CH button or the remote control: the leaf will stop;
5 press 3 times AP/CH button or the remote control: the leaf will close at standard speed;
6 when the leaf is completely closed press AP/CH button or the remote control (leaf programming
completed);
7 the DL7 LED will stop blinking and remain steady ON (programming completed and saved).
16 D760M