Briggs & Stratton 2691670 Manual Del Operador página 7

Y Differential Lock Pedal (if equipped)
Electronic Dash Panel (if equipped)
4
The electronic dash panel (Figure 4) shows the operation
status for a variety of equipment and engine parameters.
It gives clock and timer functions for oil and air filter
maintenance, and tracks work hours. The data is retained if
the battery is disconnected or power is interrupted.
Note: The Mower Deck Height display requires a wire
harness connection between the mower deck and the rider.
When you install the mower deck after maintenance, make
sure that the wire harness is correctly connected or the
Mower Deck Height display will not function.
A Control Buttons - MODE (top button), UP (center button), DOWN
(bottom button).
B Clock Display - 12-hour clock with am/pm.
C Blade Icon - Comes on when the Power Takeoff (PTO) is engaged.
D Rider Icon - Comes on when the Cruise Control is engaged.
E Message Display - Tells the operator that the unit requires
maintenance.
F Parking Brake Icon - Comes on when the Parking Brake is engaged.
G Headlight Icon - Comes on when the Headlights are engaged.
H Hour Meter - Shows the total accumulated run hours by default.
When the MODE button is pushed down, the hour meter shows the
trip hours.
I Fuel Level Bars - Comes on to show the approximate level of fuel in
the tank. At two bars, the Fuel Pump Icon will flash to remind you to
add fuel.
J Tachometer with Best Cut Range Icon - Shows the engine speed
from 1000 to 4000 RPM. The Best Cut Range shows the best
performance between the engine speed and the Mower Deck Height
settings.
K Mower Deck Height Bars - Shows the approximate height of the
mower deck.
Functions of the Hour Meter (H, Figure 4)
• By default, the Hour Meter shows the total accumulated
run hours.
• When the meter reaches 1999.9 hours, it automatically
resets to zero.
Trip Hours
• Push the MODE button (A, Figure 4) to show Trip Hours.
• Push the MODE button again and hold for 3 seconds to
reset the trip hours to zero.
Oil Hours
• Push the MODE button (A, Figure 4) two times to show
Oil Hours.
• After you change the oil and filter, push the MODE button
and hold for 3 seconds to reset the oil hours to zero.
Air Filter Hours
• Push the MODE button (A, Figure 4) three times to show
Air Filter Hours.
• After you clean or change the filter, push the MODE
button again and hold for 3 seconds to reset the air filter
hours to zero.
Clock Setting (B, Figure 4)
• Push the MODE button (A, Figure 4) four times to adjust
the clock.
• Push the MODE button again and hold it for 3 seconds to
flash the hour.
• Push the UP or DOWN button to change the hour. AM
and PM will change when the hour setting is adjusted
past 12 o'clock.
• Push the MODE button to flash the minutes.
• Push the UP or DOWN button to change the minutes.
• After you adjust the hours and minutes, push the MODE
button to return to the default clock display.
Note: If you do not push the MODE button after five seconds,
the display will not reset, and the Hour Meter will return to the
total accumulated hours.
Maintenance Messages (E, Figure 4)
Low Battery
• This message appears when a battery voltage problem
occurs.
• The display automatically clears after the battery has
been serviced.
Oil Change
• This message appears after 50 hours of run time since
the previous reset.
• After you change the oil and filter, push the MODE button
two times to show OIL HRS.
• Push and hold the MODE button for 3 seconds to reset
the timer to zero and clear the display.
Air Filter
• This message appears after 25 hours of run time.
• After you clean or change the air filter, push the MODE
button three times to show AIR FILTER HRS.
• Push and hold the MODE button for 3 seconds to reset
the timer to zero and clear the display.
7