Publicidad
Idiomas disponibles
Idiomas disponibles
G
P
P
UK
IORDANI
EGASUS
LUS
SECURING YOUR BABY
How to adjust the belts, headrest and
seat positions
IMPORTANT
The correct belt height of the
shoulder belts is attained when the belt
disappears into the shell slightly above
the shoulder of the child. Make sure that
the shoulder belts fit properly over the
shoulders of the child.
Adjusting the belts
1.
Loosen the harness straps by press-
ing the release button and pulling the
harness straps as far as you can.
Note! Do not
pull the Shoulder pads.
Ten heights of the headrest
2.
The headrest can be set at five dif-
ferent heights in group 1 mode with
the shoulder belts axle in place. There
are four additional positions in Group
2 & 3 mode once the shoulder belts
axle and harness straps has been re-
moved.
3.
Press the button on the Headrest
handle on the top of the seat. It is im-
portant to make sure the headrest fit
properly to head.
Stepless adjustment device
4.
The recline angles of the car seat can
be adjusted by front knob. Rotate
clckwise to add the recline angles,to
reduce in the opposite,ad shown from
the icon on the knob.
Securing your baby using the harness
5.
Loose the harness straps by pressing
the release button and pulling the har-
ness straps as far as you can.
I
SOFIx CAR SEAT
(9 MONHS - 11 YEARS, APPROXIMATELY)
Note!
Do not pull the shoulder pads.
6.
Open the harness buckle, then fix the
harness straps into the belt guide
band. Put the baby into the car seat.
7.
The correct height of the shoulder
belts is attained when the belt disap-
pears into the shell slightly above the
shoulder of the child. Make sure that
the harness straps fit properly over
the shoulders of the child.
8.
Slide buckle tongues together and
insert them in the buckle with an au-
dible sound "click".
9.
Pull the straps tight by the harness
adjustment strap, and make sure the
tightness is comfortable to your kid.
CAUTION
Do not twist or interchange
the harness straps.
Tightening the harness
10. CAUTION
Pull the strap end straight
towards you, not upwards or down-
wards.
Please pay attention to the strap end.
Whilst traveling (especially outside
the car) it should always be attached
to the cover.
Checklist to ensure that your baby is
buckle up correctly.
11. IMPORTANT
For the safety of your
baby, please check that...
• The harness straps of the car seat
are comfortable but firm fit around
your child.
• The harness straps are adjusted cor-
rectly in base of the child's body.
• The harness straps are not twisted.
• The buckle tongues are engaged in
the harness buckle.
24
INSTALLATION IN THE VEHICLE
Installation of Group I for the children
whose weight between 9-18kg with
ISOFIX and Top tether.
IMPORTANT
First please check if there
are 2 ISOFIX anchorings in the perpendic-
ular intersection of the vehicle seat back
and seat cushion, and the user-ready top
tether anchoring behind the vehicle seat.
Tips:
The user-ready tether anchorage
usually permanently installed on the in-
ner rear luggage shelf or on the vehicle
floor. Details you could read your vehicle
guidelines or contact the vehicle manu-
facturer.
12.
Press the ISOFIX release button and
push the ISOFIX connectors forward
as far as possible.
13.
Push the ISOFIX connectors directly
into the anchorages until you hear an
audible sound "click".
14.
Grasp the seat body to check the seat
if it is fastened tightly or shakes. If the
seat shakes and the ISOFIX connec-
tors are pulled out, please repeat the
above steps and install it again.
15.
Pull out the Top tether and press the
Tether strap release button to extend
the strap until it is long enough to
hook the User-ready tether anchor-
age behind.
16.
Hook the Tether strap hook onto the
User-ready anchorages. Check there
maybe are 3 anchorages for the hook,
please find one in your favor.
17.
Pull the Tether strap on another end
back to tighten the Top tether.
18. CATION
If the Top tether is tightened
favorably and correctly, a green
mark will turn up on the other end
of the Strap release button, please
do check it.
Installation of Group I I and it is for the
children whose weight between 15-25kg.
19.
Before the installation, please take
away the Harness system of baby car
seat.
Note:
The Baby insert, Harness
strap, Harness buckle, Buckle pads,
Shoulder pads & Shoulder belts
axle should be stored away safely
for future use (see Removing the
5-point harness system and cover).
WARNING
Do not to use any load bear-
ing contact points otherthan those de-
scribed in the instructions and marked
in the child restraint.
The belt must be routed as shown in
the instructions.
20.
Put the shoulder belt through the
shoulder belt guide under the headrest.
21.
Place your child into the baby car seat
and let the car belt pass the Belt guide.
Fasten the car belt with an audible
sound "click".
22.
Make sure the Lap belt is stretched low
and snug across the child's hips, within
the Belt guides, and fastened into the
buckle . the Shoulder belt must cross mid-
way between child's shoulder and neck.
Installation of Group I I I and it is for
the children whose weight between
22-36kg.
23.
Adjuster the height of the headrest to
suit your child.
24.
Refer to the Group II installation instruc-
tions.
Please make sure that any lap strap is
worn low down, so that the pelvis is
firmly engaged.
Installation of Group II/III with car belt
and additional connectors.
OPTIONS!
This car seat also allow to install
25
Publicidad
