Desa Remington 104316-04 Manual Para El Usuario página 21

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

CLEANING
AND
MAINTENANCE
Continued
4. Hold file guide level. Make sure 30 ° mark on
file guide is parallel to center of guide bar (see
Figure 19). This will insure that you file cutters
at 30° angle.
5. File fiom inside towards outside of cutter until
sharp. Only file in this one direction (see Figure
19). Note: Two or three strokes with file should
sharpen cutter.
6. ASter each cutter is sharpened, move chain for-
ward to sharpen next cutter. File all cutters on
one side of chain.
7. Move to other side of chain and repeat process.
Filing
Cutter
Depth
Gauges
The cutter depth gauge clearance is reduced as cutters
are sharpened. ASter every second or third sharpen-
ing, reset cutter depth gauges.
1. Place depth gauge tool (.025") firmly across top
of two cutters. Make sure depth gauge enters slot
in depth gauge tool (see Figure 21 ).
2. Use medium flat file. File depth gauge level with
depth gauge tool.
3. Remove depth gauge tool. With flat file, round
off fiont corner of cutter depth gauge (see Figure
22).
After several hand filings, have authorized service
center or shaq)ening service machine sharpen chain.
This will insure even filing.
REPLACING
SAW CHAIN
Replace chain when cutters are too worn to shaq)en or
when chainbreaks. Only use replacement chain noted in
this manual. Always include new drive sprocket when
replacing chain. This will maintain proper driving of
chain. Note: For proper chain and drive sprocket, see
Rudacement Parts and Accessories.
STORAGE
ffstonng sawfor morethgm30 &_ys, t bllow stepsbelow.
1. Drain oil tank.
2. Remove and clean guide bar and chain. Clean
guide bar and chain by soaking in petroleum
based solvent or mild soap and water mixture.
3. Dry guide bar and chain.
4. Place chain in container filled with oil. This will
prevent rust.
5. Wipe a thin coating of all over surfaceof guide bar.
6. Wipe offoutside of sawb(udy. D o this with softcloth
dampened with a mild soap and water mixture.
7. Store chain saw
• in a highor locked place, out of chil&en's reach
• in a dU place
• in a cguryingcase or with scabbgu'd over guide bgu
TECHNICAL
SERVICE
You may have fresher questionsabout assembling,
operating, or maintaining this product, ff so, you
can visit our Technical Service web site at www.
desatech.com
or contact our Technical Service
Department at 1-800-858-8501 (English Only). You
may also write to:
DESA Specialty Products
TM
P.O. Box 90004
Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
When contacting DESA Specialty Products
TM,
have
ready
• Your Name
• Your Address
• Your Phone Number
• Model Number of Product
• Date of Purchase (Include copy of receipt for
written requests).
REPLACEMENT
PARTS
AND
ACCESSORIES
_IbWARNING:
Useonly replacement parts
and accessories
described in this manual.
Use of other parts or accessories
could
damage saw or injure operator.
For original replacement parts and accessories, con-
tact your nearest Authorized Dealer or Authorized
Service Center for this product. If they can not sup-
ply the pa_ or accessory, contact your nearest Parts
Central listed on page 47. Each Authorized Dealer,
Authorized Service Center, and Parts Central is
independently owned and operated.
See pages 48 and 49 for an Illustrated Palls List.
If you need additional letemd information, contact our
Technical Service Depm_ment(see Technical S(,m'ice).
In Canada call 1-800-561-3372 for pm_sinformation.
You may purchase the following service or replace-
ment pa_s:
LNT-2
Part Number
Description
104302-01S #
Guide bar, 8" (20.3 cm)
104301S#
Chain, 8" (20.3 cm)
097567-01S
Guide bar, 10" (25.4 cm)
091371S
Chain, 10" (25.4 cm)
097568-02S
Guide bar, 12" (30.5 cm)
091373-02S
Chain, 12" (30.5 cm)
075752
Drive Sprocket
# Must order both pieces
Confinuc, d
108539
21
www, desatech.com

Publicidad

Tabla de contenido
loading

Tabla de contenido