Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
If a transmitter has not yet been memorised, the first can be memorised in Mode II as indicated in table A7.
Table "A7"
Memorizing the first transmitter in mode II
1.
Connect the motor to the mains power supply, 2 beeps are immediately heard
2.
Within 5 seconds push and hold the transmitter button to be memorised
3.
Release the button after the 3 beeps
4.
Within 5 seconds start to push the same transmitter button the same number of times equal to the required
command: 1 = "Step-by-Step" 2 = "Up" 3 = "Down" 4 = "Stop"
5.
After about 3 seconds the same number of beeps as the selected command are heard
6.
Within 2 seconds push the same transmitter button
7.
Release the button on the first of the 3 beeps which confirm the memorisation.
If at point 5 the same number of beeps equal to the selected command are not heard, simply do not push any more buttons and wait a few seconds for the programming
to finish without memorising.
After the transmitter has been memorised for the "Step-by-Step" or "Stop" commands, these commands are immediately available for use, while the movement direc-
tion must be programmed in order to use the "Up" ▲ and "Down" ▼, commands. Until the direction has been programmed, each ▲ e ▼, command from the trans-
mitter is signalled with a beep and two brief movements of the motor. Being that the movement direction cannot be programmed with the transmitter memorised in Mode
II, this operation must be performed with a transmitter memorised in Mode I or with the specific TTP or TTI programmers.
When one or more transmitters have already been memorised, others can be memorised in Mode II as indicated in table A8.
Table "A8"
Memorisation of additional transmitters in Mode II
1.
Push and hold the button to be memorised of the new transmitter (approx. 5 seconds) until a beep is heard;
then release the button
2.
Within 5 seconds push and hold the button of an old and already memorised transmitter (approx. 5 seconds)
until 2 beeps are heard; then release the button
3.
Within 5 seconds start to push the same button of the old transmitter the same number of times equal to the
required command: 1 = "Step-by-Step" 2 = "Up" 3 = "Down" 4 = "Stop"
4.
After about 3 seconds the same number of beeps as the selected command are heard.
5.
Within 2 seconds push the same button of the new transmitter
6.
Release the button on the first of the 3 beeps which confirm the memorisation.
If at point 5 the same number of beeps equal to the selected command are not heard, simply do not push any more buttons and wait a few seconds for the programming
to finish without memorising.
Note: if the memory is full (30 transmitters), 6 beeps are heard and the transmitter cannot be memorised.
A new transmitter can easily be memorised with the same characteristics as that of the old one by following the procedure in table A9.
The "new" transmitter will inherit the characteristics of the old one, i.e. if the old transmitter was memorized in Mode 1, the new one will also function in Mode 1, if the
old transmitter was memorised in Mode II then the button of the new transmitter will be associated to the same command as that of the old one.
Table "A9"
Memorizing other transmitters
1.
Press and hold down the pre-memorized button of the new transmitter for approx.
3 seconds then release the button
2.
Press and hold down the pre-memorized button of the old transmitter for approx.
3 seconds then release the button
3.
Press and hold down the pre-memorized button of the new transmitter for approx.
3 seconds then release the button
4.
Press and hold down the pre-memorized button of the old transmitter for approx.
3 seconds then release the button
5.
The memorisation of the new transmitter is confirmed with 3 beeps
Note: If the memory is full (30 transmitters), 6 beeps will indicate that the transmitter cannot be memorized.
If the programming has to be cancelled and only one transmitter memorised in Mode II is available, the procedure in table A10 can be followed; (for cancellation with
a transmitter that has not been memorised or has been memorised in Mode I, see table A5).
The following can be deleted:
Table "A10"
Cancellation of the memory with transmitter memorised in Mode II
1.
Push and release a button memorised in Mode II (it doesn't matter if the motor starts to move, the motor
should stop at point 2)
2.
Push and hold the same transmitter button (approx. 5 seconds) until a beep is heard and then release the button
3.
Keep the same transmitter button pushed until 3 beeps are heard and
release the button during the third beep.
4.
Keep the same transmitter button pushed until 3 beeps are heard and
release the button during the third beep.
➨
5.
Keep the same transmitter button pushed until 3 beeps are heard and
release the button during the third beep.
6.
To cancel everything:
Within 2 seconds, push the same transmitter button and
release the button on the first of the 5 beeps that confirm the cancellation.
• only the transmitter codes, finishing at point N. 5
• all (transmitters, manoeuvre direction, TTBUS address... ), completing the procedure up to point 6.
Example
1-4
1-4
Example
New
5s
5s
Old
Old
1-4
1-4
New
Example
New
>3s
Old
>3s
New
>3s
Old
>3s
Example
5s
7
GB
Publicidad
Tabla de contenido
