Descargar Imprimir esta página
HP LaserJet 9000 Serie Guia De Instalacion
Ocultar thumbs Ver también para LaserJet 9000 Serie:

Publicidad

Enlaces rápidos

HP LaserJet 9000 Series Maintenance Kit
Install Guide
Installationshandbuch
Guía de instalación
Guide d'installation
Guida all'installazione
Lea Esto Primero

Publicidad

loading

Resumen de contenidos para HP LaserJet 9000 Serie

  • Página 1 HP LaserJet 9000 Series Maintenance Kit Install Guide Installationshandbuch Guía de instalación Guide d'installation Guida all'installazione Lea Esto Primero...
  • Página 2 The Printer Maintenance Kit contains two Press the power button to turn the power off To replace the transfer roller assembly: Type 1 rollers, seven Type 2 rollers, one transfer (button out). Open the front door of the printer. roller assembly, and one fuser assembly. Disconnect the power cord from the AC Note: The printer shown in this guide may not outlet.
  • Página 3 Rotate the large green lever downward. Pinch the blue tab on the transfer roller Remove the new transfer roller assembly from assembly, and pull the assembly out of the its packaging. CAUTION: Do not touch the printer. black foam roller. Skin oils can damage the roller.
  • Página 4 Insert the new transfer roller assembly into the Press the white button on the large green lever, Close the front door of the printer. printer until it locks into place. and rotate the lever upward until it locks into place. NOTE: Do not force the lever into position.
  • Página 5 1 11 To replace the Type 1 and Type 2 rollers: Remove the tray by lifting the outer end while You will gain access to the rollers through the Open Tray 2 and pull it out until it stops. pulling the tray free of the printer. Repeat steps empty paper tray slots (three rollers per tray).
  • Página 6 To remove the rollers from the shafts, pinch the Remove the rollers from the plastic bag. You will Slide the new rollers onto each shaft until they tab on the end of each roller, and then slide it use one Type 1 roller and two Type 2 rollers per lock into place.
  • Página 7 Reinstall Trays 2 and 3. If you do not have an To replace the Type 2 rollers in Tray 4 CAUTION: Tray 4 could be damaged if it is optional Tray 4 (2000-sheet Input Tray), (2000-sheet Input Tray): Open the tray, then dropped.
  • Página 8 To gain access to the separation roller, slide the Pinch the tab on the end of each roller, and Locate three Type 2 rollers contained in your kit. blue roller shield toward the back of Tray 4. then slide the roller off the shaft. Um Zugang zur Trennwalze zu erhalten, Drücken Sie den Sperrhebel am Rand jeder Suchen Sie im Wartungskit drei Walzen vom...
  • Página 9 Slide the new rollers onto each shaft until they Using both hands to grasp the sides of the tray, To replace the fuser assembly: lock into place. Note: You do not need to slide reinstall Tray 4. Replace the paper, if desired. If a paper-handling output accessory is the blue shield back over the roller.
  • Página 10 If a duplex printing accessory is installed, Locate the small blue levers on each side of the Lift up on the finger handle slightly and pull the remove it by pushing downward on the green fuser assembly and rotate them toward the assembly away from the printer until it stops.
  • Página 11 Grasp the blue handle on the top of the fuser Remove the new fuser assembly from its Align the fuser assembly with the bars on each assembly with one hand. Place the other hand package. Remove any orange packing material side of the opening.
  • Página 12 Once you are sure the fuser assembly is in Avoid moving the blue, T-shaped envelope Reinstall the duplex printing accessory if it was place, rotate the blue levers away from the levers inside the printer. Note: If the envelope removed. center as shown to lock the fuser assembly in levers are moved to the top position, toner may place.
  • Página 13 To reset the maintenance kit page count for Reconnect the power cord. the control panel, use the instructions for the the HP LaserJet 9000 printer: Press and hold If you have a paper handling output accessory, following HP LaserJet products: button, then press the power button to move it back into position.
  • Página 14 HP LaserJet 9000mfp/9000Lmfp : Maintenez HP LaserJet 9040/9050 : Appuyez sur le bouton HP LaserJet 9040mfp/9050mfp : Appuyez sur enfoncée la touche 6, puis appuyez sur le d'alimentation pour mettre l'imprimante sous...
  • Página 16 © 2005 Hewlett-Packard Development Company, L.P. www.hp.com *C9152-90905* *C9152-90905* C9152-90905...