Initial Battery Charge - Peg-Perego GAUCHO SUPERPOWER Empleo Y Manutencion

INITIAL BATTERY CHARGE

!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall receptacle. Connect battery charger to battery.
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY IS INCLUDED AND MUST BE CONNECTED; see instructions 25-28
1 • Place from bumper on body and tighten four screws as shown in the drawing.
2 • Place rear bumper on body.
3 • Tighten three screws as shown in the drawing.
4 • Assemble the two parts of the steering wheel.
5 • Place the horn in the steering wheel's central hole, following the instructions in its packaging.
6 • Insert the steering wheel on the steering wheel column.
7 • Align steering wheel column holes with steering wheel: nut fits into hexagon hole, bolt into round hole.
8 • Insert the windscreen.
9 • Secure it by means of the two screws.
10 • Fit the removable seat cover as shown in the figure.
11 • Hook the front elastic bands.
12 • Position the other two elastic bands.
13 • Place seat on body. Adjust seat position. Secure it with washer and thumb nut.
14 • Join A to part B of the Roll-Bar.
15 • Join A-B to the upper section of the Roll-Bar C, insert and rotate to secure.
16 • Insert the 2 plates in the slots at the base of the Roll-Bar and hold them in place. Secure the plates and the Roll-Bar with the 2 screws provided (detail A).
17 • Insert the end of the safety belt in the slot situated centrally in the bottom of the seat, as shown in the figure.
18 • Screw the net down to the body.
19 • Snap it around the roll-bar as shown in the drawing.
20 • Insert the rear-view mirrors in the direction shown by the arrow.
21 • Place the 2 plastic signs, pressing down as you do so.
22 • Insert the antenna, pressing down as you do so, into its appropriate housing, situated on the right rear mudguard.
23 • Remove the radio from its packaging. Unscrew the cover from the battery chamber. Insert two 1.5 Volt AA batteries (not supplied with the vehicle) into the
compartment, taking care to position the positive and negative poles correctly. Close the battery compartment cover and screw into place.
24 • Insert the wire from the antenna and the radio into their appropriate housing on the dashboard, making sure to place them the right way up, as shown in the
figure.
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY. THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM
THE VEHICLE.
25/6•Open the hood. Remove the two screws from the simulated engine. Remove the simulated engine. Proceed as follows:
- Remove the battery from the packaging;
- unscrew the battery block screw;
- Position the battery;
- Lock it down using the special battery block.
27 • Plug battery terminal A into vehicle wiring terminal B.
28 • Lower the imitation motor and screw it down again. Close the hood, securing it in place with the 2 hooks. The vehicle is now ready for use.
29 • Hood support shaft.
30 • Below the box you can find four removable toy tools. To remove the box, pull out and unfasten the four couplings.
31 • A:HORN. Push the yellow button the horn will sound.
B: FM RADIO: a real removable car radio that works independently. Press button 3 to turn it on. Press button 4 to turn it off. Use the triangular buttons to
change the frequency with automatic tuning. The station will not be memorized when the radio is turned off. Use knob 2 to adjust the volume. To adjust the
time, hold down the SET button and push the HR and MIN buttons as appropriate.
The AUX (1) socket on the radio can be used for connecting MP3 devices.
C: SIMULATED START-KEY. The key provided is only a "toy key", and does not turn the vehicle on or off.
D: Accelerator/electric brake pedal. The electric braking system stops the vehicle automatically when your child lifts his foot off the pedal.
32 • To unfasten the safety belts:1 push towards the middle and simultaneously press the button; 2 detach the buckle.
33 • GEAR SHIFT LEVERS: 1: first speed. 2: second speed. R: reverse.
34 • SECOND SPEED: When the red lock-out is positioned as shown in the figure, the vehicle will run in first speed and reverse only. The turtle on the lock-out is
in the up position. To use the second gear, follow the instructions: loose the screw on the red lock-out.
35 • Remove the red lock-out.
36 • Rotate it 180° until the hare is in the up position. Insert the lock-out into the hole provided.
37 • Tighten the screw. By pushing the gearshift lever backward, the vehicle moves into second gear.
38 • Open the hood. Remove the two screws from the simulated engine. Remove the simulated engine.
39 • Unscrew and remove the battery fastener.
40 • Replace the battery. Replace the battery fastener.
41 • Connect the two plugs.
42 • Replace simulated engine in vehicle and secure with screw.
43 • Disconnect the electrical unit plug A from the battery plug B by pressing at the sides.
44 • Insert the battery charger plug into a household outlet following the enclosed instructions. Connect plug B to battery charger plug C
45 • Once the battery has been recharged, unplug the battery charger from the wall outlet, and then disconnect terminals C and B.
46 • Connect terminal B and A till you hear the final click. Once recharging is complete, don't forget to close the simulated motor with the screw.
ASSEMBLY INSTRUCTIONS
BATTERY INSTALLATION
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
BATTERY REPLACEMENT
BATTERY RECHARGE