Before Starting The Equipment - Parkside PHDB 4 C3 Instrucciones De Utilización Y De Seguridad

Hidrolimpiadora de gasolina
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

9.2 Fitting the hose holder (Fig. 1, 2)
• Fit the hose holder (13) onto the bow-type handle (1) by
aligning the holes in the two components.
• Attach the hose holder (13) to the bow-type handle (1) with
four self-tapping screws (28).
9.3 Fitting the upper spray gun holder on the
handle (Fig. 4)
Use the two screws (29) to attach the upper spray gun holder
(5) to the bow-type handle (1).
9.4 Fitting the lower spray gun holder on the
tubular frame (Fig. 4)
Push the lower spray gun holder (12) onto the tubular frame
(7) and push it upwards along the tubular frame (7) until it is
clamped.
9.5 Fitting the wheels (Fig. 5)
• Push the axle (31) from outside through the wheel (10).
• Now guide the axle (31) with the wheel (10) from the out-
side into the tubular frame (7) and secure it in place with the
R-clip (32).
• Repeat the process on the opposite side.
9.6 Fitting the rubber foot (Fig. 5)
Attach the rubber foot (33) with the washer (30) and nut (34)
onto the tubular frame (7).
9.7 Fitting the hand spray gun, jet pipe (Fig. 6, 7, 8)
m DANGER
• Risk of injury! Appliance, supply pipes, high-pressure hose
and connections must be in perfect working order. If the
equipment is not in perfect working order, the appliance
may no longer be used.
• Always tighten the fixing by hand! Too loose a connection
can lead to disconnection and cause injury.
• Connect the jet pipe (11) to the hand spray gun (2).
• Tighten the screws of the jet pipe (11) by hand.
• Fit the high-pressure hose (6) onto the hand spray gun (2)
• Attach the high pressure hose (6) to the water outlet (16) by
turning the fixing.

10. Before starting the equipment

10.1 Filling/checking the engine oil (Fig. 10)
ATTENTION
• The engine oil must be filled before the first use!
• Check the oil level before each use.
• Do not use the appliance if there is no oil visible on the
dipstick (43).
• Do not overfill the oil. A too high oil level can cause engine
damage.
• Add oil as required. Use only engine oil (SAE10W30).
• Place the device on a flat, even surface and remove any
dirt from the area around the oil inlet/dipstick (42)/oil tank
cover with oil dipstick (43).
• Open and remove the oil tank cover with oil dipstick (43) by
turning anticlockwise.
• Fill the system with max. 400 ml four-stroke engine oil
(SAE10W30) as required.
46
GB/MT
• Check the oil level using the marks on the oil dipstick.
• Place on the oil tank cover with oil dipstick (43) and close
by turning clockwise.
10.2 Adding fuel (Fig. 11)
m DANGER
RISK OF FIRE AND EXPLOSION!
• Never refuel in confined spaces or when the engine is run-
ning or still hot.
• Do not smoke while refuelling.
• Do not use any two-stroke mixture.
• Do not refuel in the vicinity of open flames or sparks.
• Do not spill fuel – use a funnel.
• Wipe up any spilt fuel.
• After refuelling, close the fuel canister and the tank properly.
• Open and remove the fuel tank cover (14) by turning anti-
clockwise.
• Place a funnel (37) in the opening of the fuel tank (15).
• Fill the fuel tank (15) with fuel up to max. 3–4 cm below the
top edge.
• Replace the fuel tank cover (14) and close the fuel tank (15)
by turning clockwise.
10.3 Connecting the water supply (external) to the
pump (Fig. 12)
m WARNING
• If the inlet sieve is missing or damaged, do not operate
the high-pressure cleaner. Particles in the high-pressure jet
can cause injury.
ATTENTION
• The length of the free garden hose must be at least 3 m
between the inlet of the high-pressure cleaner and a shut-
off device, such as a Y shut-off coupling or other suitable
shut-off valve.
• Do not operate the high-pressure cleaner without a water
supply. If the high-pressure cleaner is operated without wa-
ter, the high-pressure cleaner will be damaged.
• Before connecting the garden hose (NOT included in the
scope of delivery) to the water inlet (21), check the inlet
sieve. Clean a contaminated inlet sieve, replace a damaged
inlet sieve.
• To remove all impurities, run water through the garden hose
for 30 seconds. Shut off the water. Important: Do not suction
stagnant water for the water supply. Only use water up to a
maximum of 40 °C.
• Fit the hose connection adapter (41) on the water inlet (21).
• The garden hose (NOT included in the scope of delivery)
can be equipped with the enclosed quick connector (40).
• Connect the garden hose (NOT included in the scope of
delivery) to the water inlet (21). The hose must not be longer
than 15 m.
• Check that the hose is tightly fitted.

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido