Bestway POWER STEEL Manual Del Usuario página 5

U-Support Spring-
C-Connector
loaded Pin
Size of pool
QTY Part No. QTY
2.82mx1.96mx84cm
4 P61361 16
(111"x77"x33")
4.04mx2.01mx1.00m
4 P61361 20
(159"x79"x39.5")
4.12mx2.01mx1.22m
4 P61361 20
(162"x79"x48")
4.88mx2.74mx1.22m
4 P61282 24
(16'x9'x48")
4.88mx4.88mx1.22m
4 P61282 32
(16'x16'x48")
5.49mx2.74mx1.22m
4 P61282 24
(18'x9'x48")
6.71mx3.66mx1.32m
4 P61282 32
(22'x12'x52")
7.32mx3.66mx1.32m
4 P61282 36
(24'x12'x52")
9.56mx4.88mx1.32m
4 P61282 48
(31.3'x16'x52")
C-Connector
Top Rail
Top Rail
U-Support B
U-Support A
NOTE: Drawing only for (111'' x 77'' x 33''),
NOTE: Drawing for illustration purpose only. May not reflect actual product. Not to scale.
Top Rail Combinations
No. of U-shaped
Size of pool
support Long Side
2.82mx1.96mx84cm
8
(111"x77"x33")
4.04mx2.01mx1.00m
10 B-E-A
(159"x79"x39.5")
4.12mx2.01mx1.22m
10 B-E-A
(162"x79"x48")
4.88mx2.74mx1.22m
12 D-F-F-E
(16'x9'x48")
4.88mx4.88mx1.22m
16 D-F-F-E
(16'x16'x48")
5.49mx2.74mx1.22m
12 B-A-A-C
(18'x9'x48")
6.71mx3.66mx1.32m
16 B-A-A-A-C
(22'x12'x52")
7.32mx3.66mx1.32m
18 B-A-A-A-A-C
(24'x12'x52")
9.56mx4.88mx1.32m
24 B-A-A-A-A-A-A-C
(31.3'x16'x52")
PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE.
CHOOSE THE CORRECT LOCATION
NOTE: The pool must be set up on a completely flat and level surface. Please do not install the
pool if the surface is inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the entire time the
pool is installed, moreover the location must be flat and must be cleared of all objects and debris
including stones and twigs.
• We recommend positioning the pool away from any objects children could use to climb into the pool.
NOTE: Position the pool near an adequate drainage system to deal with overflow or to discharge the
pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse causing serious personal injury and/or damage to personal
property and will void the warranty and prevent any service claims.
• Sand should not be used to create a level base; the ground must be dug out if necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain underground
utility pipes, lines or cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces. The selected
location should be firm enough to withstand the pressure of the water; mud, sand, soft / loose soil or
tar are not suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to develop,
therefore we recommend removing all grass from the selected pool location.
• Avoid areas prone to aggressive plant and weed species that may grow through the ground cloth or
liner.
NOTE: Check with your local city council for by-laws relating to fencing, barriers, lighting and safety
requirements and ensure you comply with all laws.
NOTE: If have a filter pump, refer to the pump's manual for instructions.
NOTE: The ladder must match the pool size and should to be used only for entering and exiting the
pool. It is forbidden to exceed the permitted payload of the ladder. Check regularly if the ladder is
properly assembled.
Small U- Big U-Support
Support Cap Cap
Part No. QTY Part No. QTY Part No.
P61366 16 P61367 / /
P61366 20 P61367 / /
P61366 20 P61367 / /
P61286 / / 24 P61287
P61286 / / 32 P61287
P61286 / / 24 P61287
P61286 / / 32 P61287
P61286 / / 36 P61287
P61286 / / 48 P61287
(159" x 79'' x 39.5''), (162'' x 79'' x 48'') Size of Pool.
No. of Top Rail
Short Side A B C D E
B-A C-D 2 2 2 2 0
C-D 2 2 2 2 2
C-D 2 2 2 2 2
D-E 0 0 0 4 4
D-F-F-E 0 0 0 4 8
D-E 4 2 2 2 2
E-D-F 6 2 2 2 2
E-D-F 8 2 2 2 2
D-F-F-E 12 2 2 2 2
Installation
Sleeve for C-
Assembly of the Rectangular Frame Pool can be completed without tools.
connector
Bestway Inflatables will not be responsible for damage caused to the pool due to mishandling or
QTY Part No.
failure to follow these instructions.
1. Lay out all parts and check that you have the correct quantities as listed in the components list.
8 P61365
If you are missing any part do not assemble the pool, contact Bestway Customers Service.
2. Spread out the pool and make sure the pool is right side up, let it sit exposed to direct sunlight
8 P61365
for 1 hour or more so that the pool is more flexible during set up.
3. Place the pool near an adequate drainage system to deal with overflow water and ensure the
8 P61365
pool's inlet A and outlet B are correctly positioned to allow your filter pump to connect to a power
source. Note: Do not use extension power cords to power your pump.
8 P61285
ATTENTION: Do not drag the pool on the ground, this can damage the pool.
4. Insert the stopper plugs into inlet A and outlet B on the wall from the inside of the pool.
8 P61285
NOTE: For pool with connection valve, please refer to the connection valve installation on
following page.
8 P61285
5. Assemble the Top Rails. Start with the long side of the pool, begin by sliding Top Rail B into the
pool sleeve. Connect Top Rail A or Top Rail E to Top Rail B, ensure the spring-loaded pins snap
8 P61285
into the pre-drilled holes. Be sure to reference the Top Rail Combination Chart to determine the
correct configuration for your pool. Continue connecting and inserting additional Top Rails. Be
8 P61285
sure to line up the holes in the rails with the holes on the sleeves. (See Fig.1)
6. Insert the C-Connectors into the Top Rails. (See Fig. 2.1/2.2)
8 P61285
7. Install the U-Support; first insert the U-Support through the Pole Support at the bottom of the
pool (See Fig. 3.1/3.2), then insert the two ends of the U-Support into the exposed holes on the
Top Rail (See Fig. 3.3), ensure the spring-loaded pins snap into position. Repeat this procedure
for the remaining U-Supports.
NOTE: Complete one side of the pool before moving to the other side.
8. Pull the bottoms of the U-Support outward away from the liner and make the Pole Support taut.
Repeat this procedure for remaining U-Supports.
9. Ensure drain valve is firmly closed.
10. Put 1" to 2" (2.5cm to 5cm) water in the pool to cover the floor. Once pool floor is slightly
covered, gently smooth out all wrinkles. Start in the center of the pool and work your way
clockwise to the outside. (See Fig.4)
Fig. 1
Fig. 2.2
C-Connector
F
Fig. 3.1
0 4
0 4
0 4
4 4
4 4 Fig. 4
0 4
2 4
2 4
4 4
Connection Valve Assembly
For pool with connection valve.
(See Fig.6)
Fig.6
5
Fig. 2.1
Fig. 3.2 Fig. 3.3
Fig. 5
A
B
S-S-004555