Tabla de contenido
Publicidad
enter the 3 digit of the address of the 1st
external door station to be stored (codes
from 231 to 250) following the procedure
reported on the paragraph "Entering codes
or addresses" ;
press the button
to confirm the present
address move to the 2nd one; an acknowl-
edge tone will be heard;
enter the 3 digit of the address of the 2nd
external door station and confirm by press-
ing button
;
proceed entering the addresses of the 3rd
and 4th external stations (if present) or exit
the present programming phase pressing
several times the button
back to selecting programming mode;
proceed with another programming or exit
programming mode by pressing button
.
Note: store only the addresses of the exter-
nal door stations to which the user can be
connected. Don't store the addresses of
external door stations belonging to differ-
ent buildings even if in the same installa-
tion.
Buttons 1,2,3,4,5 and 6.
These buttons can be used to:
make intercommunicating calls;
- to call users of different apartments it is
necessary to store in each button of your
monitor the address of the user you wish to
call pressing that button (codes from 001 to
200).
- to call other videointercoms installed in the
same apartment (local intercommunicating
service), it is necessary to store in the
buttons 1,2,3,4,5,6 of each monitor always
the code 000; start from button 1 and go on
until you have programmed, with the code
000, as many buttons as are the video-
intercoms installed in the apartment (max 6
units) you wish to call; automatically by
pressing buttons 1,2,3,4,5 of one unit you
will call the unit whose internal address is
related to the pressed button according to
table 2.
Table 2.
Addresses for intercommunicating calls
Internal
Button to press
address
1
2
3
000
001
002
003
001
000
002
003
002
000
001
003
003
000
001
002
004
000
001
002
005
000
001
002
For example if you press the button 3 from the
videointercom whose intercommunicating
address is 002 you will call the intercommu-
nicating user 003.
monitoring external door stations (it is
suggested to use button
to monitor the 1
external door station) to enable this feature
store the address of the external door station
(codes from 231 to 250).
optional functions operated by means of
the actuators art.2281; to enable this
functions store the address of the actuator to
be operated (codes from 211 to 220).
To make the programming it is necessary:
enter the programming mode following the
instructions described in " Enter the
programming mode ";
a - keep pressed for more than 4 seconds the
button you wish to program; red LED starts
flashing;
b -enter the 3 digit of the code of the desired
, you will be led
function following the procedure reported on
the paragraph "Entering codes or
addresses";
c -press the button
or
tone will be heard and the red LED lights-ON
continuously;
repeat phases a-b-c to program the other
buttons or exit the programming mode press-
ing button
Notes.
- In each button can be stored only one code.
- Intercom conversations or connections with
users and external stations of other buildings
will not be possible if digital exchanger art.2273
is installed.
Programming the number of ringing call
enter the programming mode following the
instructions described in " Enter the
programming mode ";
a - press button
heard;
b - to press left and right the button
respectively increase or decrease the
number of rings. After each pressure of the
button the selected number of rings will be
heard;
c - press one of the buttons (1,2,3 or 4) to
select the type of call you wish to change ( see
table 3 );
if it's required to modify the number of ringing
call of another type of call, repeat points a-
b-c;
proceed with other programming phases or
exit the programming mode pressing the
button
4
5
004
005
004
005
004
005
To make the programming easier and to remind your self the stored codes, please fill in the
004
005
following table
003
005
003
004
st
; an acknowledge
or
; red LED turns-OFF.
; only one ring will be
or
; red LED turns-OFF.
Programming a melody for a call type
enter the programming mode following the
instructions described in " Enter the
programming mode" ;
a - press the button
; the melody actually
programmed will be heard;
b - to push laterally (left or right side) the
button to select the previous or next ringer
tone;
c - press one of the button 1,2, 3 or 4 to select
the type of call to modify ( see table 3 );
if it is required to modify the melody of
another type of call, repeat the points a-b-c;
exit the programming mode pressing the
button
or
; red LED turns-OFF.
Table 3.
Buttons to programming the type of call
Button
Type of call
1
from external door station
2
from other users
3
intercommunicating
4
floor (local)
Exit the programming phase
In any situation it is possible to exit the
programming mode by pressing the button
or
.
to
Mi 2384
- 15 -
Publicidad
Tabla de contenido
