Guidance And Manufacturer's Declaration - Kinetec CPM concept Manual De Empleo

Product information

Guidance and manufacturer's declaration

Electromagnetic emissions
The « KINETEC Centura Elbow Module» is intended for use in the electromagnetic environment specified below. The customer or the user
of the « KINETEC Centura Elbow Module» should assure that it is used in such an environment.
Emissions test
Radio-Frequency emissions
CISPR 11
Radio-Frequency emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations / Flicker emissions
IEC 61000-3-3
Electromagnetic immunity
The « KINETEC Centura Elbow Module» is intended for use in the electromagnetic environment specified below. The customer or the user
of the « KINETEC Centura Elbow Module» should assure that it is used in such an environment.
Immunity test
Electrostatic discharge (ESD)
IEC 61000-4-2
Electrical fast transient / burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage interruptions
CEI 61000-4-11
Voltage dips and voltage
variations on power supply input
lines
CEI 61000-4-11
Power frequency (50/60 Hz)
magnetic field
IEC 61000-4-8
NOTE : U is the a.c. mains voltage prior to application of the test level.
T
GB
18
Compliance
The « KINETEC Centura Elbow Module» uses RF energy only for its internal
Group 1 function. Therefore, its RF emissions are very low and are not likely to cause
any interference in nearby electronic equipment.
Class B
The « KINETEC Centura Elbow Module» is suitable for use in all establishments
Class A including domestic and those directly connected to the public low-voltage power
supply network that supplies buildings used for domestic purposes.
Complies
IEC 60601
Test level
±2 kV, ±4 kV, ±6 kV
contact
±2 kV, ±4 kV, ±8 kV
air
±2 kV for power supply
lines
±1 kV for input/output lines
±0,5 kV, ±1 kV differential
mode
±0,5 kV, ±1 kV, ±2 kV
common mode
< 5% U
T
(>95% dip in U )
T
for 5 seconds
< 5% U
T
(>95% dip in U )
T
for 0,5 cycle
40% U
T
(60% dip in U )
T
for 5 cycles
70% U
T
(30% dip in U )
T
for 25 cycles
3A/m
Electromagnetic environment – guidance
Compliance level
±2 kV
There is a reset of the « KINETEC Centura
contact
Elbow Module». After turning on, check up
the operating parameters, then push START
±2 kV, ±4 kV, ±8 kV
to begin the session.
air
±2 kV for power supply
lines Mains power quality should be that of a
typical commercial or hospital environment.
±1 kV for input/output lines
±0,5 kV, ±1 kV differential
mode
Mains power quality should be that of a
typical commercial or hospital environment.
±0,5 kV, ±1 kV, ±2 kV
common mode
At the interruption, there is a reset of the
< 5% U « KINETEC Centura Elbow Module». After
T
(>95% dip in U ) turning on, check up the operating
T
for 5 seconds parameters, then push START to begin the
session.
< 5% U
T
(>95% dip in U )
T
for 0,5 cycle
40% U
T
Mains power quality should be that of a
(60% dip in U )
T
typical commercial or hospital environment.
for 5 cycles
70% U
T
(30% dip in U )
T
for 25 cycles
Power frequency magnetic fields should be
3A/m at levels characteristic of a typical location in
a typical commercial or hospital environment.
Electromagnetic environment – guidance